Seat - Remove and Install
Show/hide table
 |
|
In order to prevent possible personal injury, release the air pressure from the air tank before disconnecting any components of the air system. |
- Refer to Operation and Maintenance Manual, "Use of Wheel Chocks".
- Refer to Operation and Maintenance Manual, "Battery Disconnect Switch".
- Refer to Operation and Maintenance Manual, "System Pressure Release"Air System.
Show/hide table
Illustration 1 g01178311 - Slide seat (1) to the full back position. Remove bolt (2). Slide seat (1) forward.
Show/hide table
Illustration 2 g01178312 - Remove cable strap (3). Disconnect hose assembly (4). Remove clip (5).
Show/hide table
Illustration 3 g01178313 - Remove clip (6). Remove bolts (7). Position bracket (8) out of the way.
Show/hide table
Illustration 4 g01178314 - Remove bolts (9). Move seat suspension group (10) backward.
Show/hide table
Illustration 5 g01178315 - With the help of another person, remove seat (1). The weight of seat (1) is approximately
32 kg (70 lb) .Show/hide table
Illustration 6 g01178316 - With the help of another person, remove suspension group (10). The weight of suspension group (10) is approximately
34 kg (75 lb) .Show/hide table
Illustration 7 g01178319 - Remove support assembly (11), if necessary.
- Install seat (1) in the reverse order of removal.
Caterpillar Information System:
2012/08/28 An Improved Filter Group is Now Available For Certain D5N Track-Type Tractors and 561N Pipelayers {3004, 3016, 3067}
CW14 Pneumatic CompactorEngine Supplement Battery - Remove and Install
Commissioning Procedure For the 797F and the 797F XQ Off-Highway Truck {0374, 1000, 7000, 7961} Commissioning Procedure For the 797F and the 797F XQ Off-Highway Truck {0374, 1000, 7000, 7961}
Commissioning Procedure for the 793F, 793F Tier 4, and the 793F CMD Off-Highway Truck {1000, 7000, 7961} Commissioning Procedure for the 793F, 793F Tier 4, and the 793F CMD Off-Highway Truck {1000, 7000, 7961}
PL83 and PL87 Pipelayer Systems Speed Sensor (Transmission Output)
990K Wheel Loader Systems Speed Sensor (Transmission Input)
824K Wheel Dozer, 825K Soil Compactor and 826K Landfill Compactor Machine Systems Pressure Sensor (Steering Pilot Oil)
988K Wheel Loader Systems Pressure Sensor (Torque Converter Impeller Clutch Oil)
CP56B, CP68B, CS56B and CS68B Vibratory Soil Compactors Propel System Propel Lines
834K Wheel Dozer Systems and 836K Landfill Compactor Systems Modulating Valve (Torque Converter Impeller Clutch)
R3000H Load Haul Dump Power Train MID 081 - CID 0627 - FMI 04
R3000H Load Haul Dump Power Train MID 081 - CID 0627 - FMI 03
CB34B, CB34B XW, CB36B and CC34B Utility Compactors Operator Controls
CW14 Pneumatic CompactorEngine Supplement Fuel Priming Pump and Fuel Filter Base - Remove and Install
2012/09/06 New Onboard Software Version 6.8 Is Now Available for Cat® Terrain for Draglines on Certain Machine Control and Guidance Products {7490, 7605}
789D and 789D XQ Off-Highway Trucks Machine Systems Tire and Rim (Front) - Remove and Install
2012/09/06 A New Flywheel Speed Sensor Is Used on Certain 3500 Off-Highway Truck Engines {1907}
CW14 Pneumatic CompactorEngine Supplement Clean Emissions Module - Remove and Install
Incorrectly Machined Bearing Cage May Cause Bearing to Lose Oil Film{3075, 3159, 7551} Incorrectly Machined Bearing Cage May Cause Bearing to Lose Oil Film{3075, 3159, 7551}
CB44B and CB54B Vibratory Asphalt Compactors Engine Supplement Engine - Remove and Install
C13 Tier 4 Final Engines Air in Fuel - Test
2012/08/16 A New Bracket for the Cab on the 795F Off-Highway Truck is Now Available {4459, 7150, 7301}
270-8312 Strut Handler{0599, 0756, 7200, 7201} 270-8312 Strut Handler{0599, 0756, 7200, 7201}
2012/11/12 An Improved Proportional Control Assembly Is Now Used On Certain M Series and M Series 2 Motor Graders {5702, 7332}