The Breather for Steering Tank Is Now Relocated on 793F Off-Highway Trucks {5057}
- Off-Highway Truck:
- 793F (S/N: SND1-UP; SSP1-UP)
Description of Change: The new location improves the performance of breather, since the new location is less susceptible to dust from the tires.
Adaptable To: The 157-7911 Breather is part of 278-8454 Hydraulic Oil Lines Gp .
The relocation of the breather is adaptable to the machines SSP1-435 and SND1-114.
The new location of the breather is effective in production with the machines SSP436-UP and SND115-UP.
Show/hide table
Parts Required to Relocate 157-7911 Breather     | |||
Item     | Qty     | Part Number     | Description     |
3     | 1     | 124-2137     | Coupling     |
4     | 2     | 228-7092     | O-Ring Seal     |
5     | 1     | 377-8722     | Plate As     |
6     | 1575 mm (62.0 inch)     |
122-6872     | Hydraulic Hose     |
7     | 1     | 6V-9007     | Elbow     |
8     | 3     | 238-5082     | O-Ring Seal     |
9     | 1     | 8T-7529     | Clip     |
10     | 1     | 124-2121     | Permanent Coupling     |
11     | 1     | 8C-8400     | Elbow     |
Show/hide table
Illustration 1 | g02661512 |
Former location of the 157-7911 Breather . |
Show/hide table
Illustration 2 | g02661513 |
New location of the 157-7911 Breather . |
Use the following procedure to relocate the breather:
- Remove breather (1) from the former location that is shown on Illustration 1, save the part.
- Remove plate assembly (2) and discard the part. Install new plate assembly (5) in place of plate assembly (2) .
- Install elbow (11) with a new O-ring seal (8) .
- Build new hose assembly with new hydraulic hose (6), new coupling (3), and permanent coupling (10). Connect one end of hose assembly to elbow (11) with a new O-ring seal (4) .
- Use elbow (7), two new O-ring seals (8) to install breather (1) to plate assembly (5). Use the part that was saved in Step 1.
- Connect the other end of the hose assembly to the elbow (7) with a new O-ring seal (4) as shown in Illustration 2.
- Use a new clip (9) to secure the hose assembly as shown in Illustration 2.
Caterpillar Information System:
2012/12/24 Triple Flange Idler Available for Compact Track Loader {4159}
773G and 775G Off-Highway Truck Cooling System Water Temperature Regulator - Replace
735B, 740B and 740B EJECTOR Articulated Trucks Engine Supplement Exhaust Bellows - Remove and Install
2570C and 2670C Wheel Feller Bunchers Monitoring System
773G and 775G Off-Highway Truck Cooling System Pressure Cap - Clean/Replace
C175-16 Locomotive Engine Engine Oil Pressure Sensor
XQ60 Rental Generator Set After Starting Engine
773G and 775G Off-Highway Truck Cooling System Coolant Sample (Level 2) - Obtain
773G and 775G Off-Highway Truck Cooling System Coolant Sample (Level 1) - Obtain
SH-56B Felling Head Felling Head Grapple Arm - Remove
Product Link - PL522/523 MID 161 - CID 1888 - FMI 14
773G and 775G Off-Highway Truck Cooling System Coolant (ELC) - Change
SH-56B Felling Head Felling Head Accumulator Arm - Remove and Install
2013/03/08 Compact Track Loader Track Derailment Prevention and Repair Guidelines {4151}
SH-56B Felling Head Felling Head Grapple Arm - Install
2570C and 2670C Wheel Feller Bunchers Battery - Clean
2570C and 2670C Wheel Feller Bunchers Battery Hold-Down - Tighten
Procedure to Prevent Damage to the Rear Chassis Harness Assembly on Certain Motor Graders{1408} Procedure to Prevent Damage to the Rear Chassis Harness Assembly on Certain Motor Graders{1408}
HH44 DE Harvester Head Hydraulic Fittings - Inspect
773G and 775G Off-Highway Truck Radiator Core and Aftercooler - Clean
2570C and 2670C Wheel Feller Bunchers Brake Accumulator (Service) - Check
2570C and 2670C Wheel Feller Bunchers Cab Air Filter - Clean/Replace
Installation Procedure of 333-2727 Snow Blade and Mounting Gp for 140M and 160M Motor Graders {6158, 6159} Installation Procedure of 333-2727 Snow Blade and Mounting Gp for 140M and 160M Motor Graders {6158, 6159}
563C and 573C Wheel Feller Bunchers Cooling System Coolant Sample (Level 1) - Obtain