Electronic Control Module (ECM) - Configure
电子控制模块的配置
配置电子控制模块(ECM)所需要的工具如表格 1 所示。
Show/hide table
所需工具     | ||
零件号     | 说明     | 数量     |
317-7484     | Caterpillar 电子技师(Cat ET)维修工具     | 1     |
317-7485     | 通信适配器 III     | 1     |
317-7487     | USB 至 PC 电缆     | 1     |
327-8981     | 数据链路电缆     | 1     |
Cat ET 维修工具用于访问配置屏幕。 Cat ET 维修工具屏幕上的信息将给出引导用户完成步骤的说明。 有关 Cat ET 的更多信息,请参阅与 Cat ET 维修工具软件一起提供的手册。
Show/hide table
图 1 | g01896613 |
这是位于数据链路两个底座之间的维修接头的典型视图。 |
当更换 ECM 后,必须配置 ECM。 配置屏幕仅用于具有 ECM 的机器。 ECM 需要在开始校准前配置。
检查配置屏幕可解决机器问题。 部件故障可识别为以下项:
- 未安装该部件。
- 已安装该部件但需要更改安装以排除故障。
依照以下说明访问配置屏幕:
- 将通讯适配器和计算机连到诊断维修工具接头上。
- 起动 Cat ET 维修工具。
- 选择 "File(文件)"。
- 转到"选择 ECM"。
- 选择"底盘 ECM"。
- 转到 "Service(维修)"菜单。
- 选择 "Configuration(配置)"。
- 单击 "OK"。
注: 可更改附件或首选项的特定操作或特征。
Caterpillar Information System:
2008/12/08 A New Torque Sequence for the Valve Cover Is Now Used {1107}
854K Wheel Dozer and 992K, 993K Wheel Loaders VIMSTM 3G / Product Link Wiring Harness (Short Circuit) - Test
541 Track Feller Buncher, 551 Track Feller Buncher and 552 Track Feller Buncher Machine Systems Relief Valve (Line) - Test and Adjust
854K Wheel Dozer and 992K, 993K Wheel Loaders VIMSTM 3G / Product Link Wiring Harness (Open Circuit) - Test
793F and 797F Off-Highway Trucks Chassis Electronic Control System Electrical Connector - Inspect
Intermittent Erratic Shifting and Derated Engine rpm{1000, 3030, 3101} Intermittent Erratic Shifting and Derated Engine rpm{1000, 3030, 3101}
Procedure to Retrofit a Diesel Particulate Filter (DPF) for Emissions on a IT62G Integrated Toolcarrier, and on 950F Series II, 950G, and 962G Wheel Loaders{1061, 108F, 1091} Procedure to Retrofit a Diesel Particulate Filter (DPF) for Emissions on a IT62G Integrated Toolcarrier, and on 950F Series II, 950G, and 962G Wheel Loaders{1061, 108F, 1091}
2009/01/26 New Plate Assemblies Updated the Lighting Wiring Group and the Platform Wiring Group {1408, 1429}
793F and 797F Off-Highway Trucks Chassis Electronic Control System Electrical Output Components
2008/12/22 Test and Adjusting, RENR6480 Has Been Updated on SIS Web. {5070, 5070}
12K, 140K, 140K Series 2 and 160K Motor Graders Hydraulic and Steering System Valve and Linkage Group
120K and 120K Series 2 Motor Graders Machine Systems Seat - Remove and Install
793F Series AC Off-Highway Truck Chassis Electronic Control System General Information
793F and 797F Off-Highway Trucks Chassis Electronic Control System Electrical Component and Connector Locations
793F and 797F Off-Highway Trucks Chassis Electronic Control System Diagnostic Capabilities
793F and 797F Off-Highway Trucks Chassis Electronic Control System Event Code List
R2900G Load Haul Dump Cab Air Filter - Clean/Replace - If Equipped
735, 740 and 740 EJECTOR Articulated Trucks Machine Systems Brake Control Valve (Service)
795F AC and 795F AC XQ Off-Highway Truck Engine Supplement Guard (Engine Oil Pan) - Remove and Install
795F AC and 795F AC XQ Off-Highway Truck Engine Supplement Engine - Remove
795F AC and 795F AC XQ Off-Highway Truck Engine Supplement Engine - Install
Rework for the Implement Gear Pump {5055, 5070, 5073} Rework for the Implement Gear Pump {5055, 5070, 5073}
120K and 120K Series 2 Motor Graders Machine Systems Air Tank - Remove and Install
2008/12/08 Replacement Engines are Available for Legacy Machines {1000}