Piston Motor (Fan Drive) - Remove
拆卸步骤
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 8T-0162 | 螺栓 | 2 |
| 6F-7831 | 垫圈 | 1 | |
| 126-7183 | 十字挡块 | 1 | |
| 126-7182 | 螺母 | 1 | |
| 6V-2360 | 硬垫圈 | 1 | |
| B | 255-8933 | 螺栓 | 1 |
| C | 138-7575 | 连杆支架 | 2 |
开始:
- 拆下风扇。 请参阅拆解和组装, "风扇 - 拆卸和安装"，以了解正确的步骤。
注: 清洁度是一项重要的因素。 拆卸步骤开始之前，应彻底清洁部件外部。 这有助于防止尘土进入内部结构。
- 拆下螺栓 (1) 和垫圈。
Show/hide table
 | |
| 图 1 | g01629416 |
- 拆下垫片 (2) 。 记下垫片数量，以便于安装。
Show/hide table
 | |
| 图 2 | g01629713 |
- 使用工具 (A) 将轮毂 (3) 从活塞式液压马达 (4) 上脱开。
Show/hide table
 | |
| 图 3 | g01630834 |
Show/hide table
 | |
| 图 4 | g01630853 |
- 拆下工具 (A) ，然后安装工具 (B) 和工具 (C) 。 连接适当的起吊设备，然后拆下轮毂 (3) 。 轮毂 (3) 的重量约为 40 kg (88 lb)。
- 断开软管 (6) 和软管组件 (5) 。 拆下盖 (7) 。
Show/hide table
 | |
| 图 5 | g01630958 |
注: 翻转该单元以检修马达。
- 将适当的起吊设备连接到活塞式液压马达 (4) 上。 活塞式液压马达 (4) 的重量约为 200 kg (440 lb)。
Show/hide table
 | |
| 图 6 | g01631176 |
- 卸下螺栓 (8) ，然后卸下活塞式液压马达 (4) 。
Caterpillar Information System:
2008/12/08 A New Procedure to Adjust the Charge Relief Valve is Available {4350, 4350}
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Power Train Tie Rod (Steering)(Front) - Remove and Install - Two-Wheel Drive
795F AC and 795F AC XQ Off-Highway Truck Machine Systems Pad (Truck Body Mounting) - Install
795F AC and 795F AC XQ Off-Highway Truck Machine Systems Pad (Truck Body Mounting) - Remove
785D OEM Off-Highway Truck Power Train Axle Shaft - Install
785D OEM Off-Highway Truck Power Train Axle Shaft - Remove
430E Backhoe Loader Bank Valve - Remove and Install
2015/07/17 A New Cylinder Pack Is Now Used {1225, 1239}
New Piston Pin Is Now Available in 3400 Cylinder Packs {1225, 1239} New Piston Pin Is Now Available in 3400 Cylinder Packs {1225, 1239}
Reuse and Salvage for 3500 Engine Cylinder Blocks {0672, 0705, 0762, 1201, 1217} Reuse and Salvage for 3500 Engine Cylinder Blocks {0672, 0705, 0762, 1201, 1217}
AccuGrade For Wheel Tractor-Scrapers Electrical Power Supply (GPS Receiver)
AccuGrade For Wheel Tractor-Scrapers Electrical Power Supply (Display)
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Power Train Tie Rod (Steering)(Front) - Remove and Install
795F AC and 795F AC XQ Off-Highway Truck Machine Systems Piston Motor (Fan Drive) - Install
785D OEM Off-Highway Truck Power Train Gear Pump (Rear Axle Lubrication) - Remove
785D OEM Off-Highway Truck Power Train Gear Pump (Rear Axle Lubrication) - Install
430E Backhoe Loader Counterweight - Remove and Install
430E Backhoe Loader Refrigerant Compressor - Remove and Install
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Power Train Steering Cylinder (Front) - Remove and Install - Two-Wheel Drive
430E Backhoe Loader Air Conditioner and Heater Components - Remove and Install
422E, 428E, 432E, 434E, 442E and 444E Backhoe Loaders Power Train Steering Cylinder (Front) - Remove and Install
785D OEM Off-Highway Truck Power Train Flow Control and Relief Valve (Rear Axle Oil) - Remove
785D OEM Off-Highway Truck Power Train Flow Control and Relief Valve (Rear Axle Oil) - Install
2008/08/25 The Torque Specification on the Rocker Arm Bolts has Changed {1102, 1123}