Personal injury can result from rotating and moving parts. Stay clear of all rotating and moving parts. Never attempt adjustments while the machine is moving or the engine is running unless otherwise specified. The machine must be parked on a level surface and the engine stopped. Attach a "Do Not Operate" or similar warning tag to the start switch and controls before servicing, repairing, or making adjustments to the machine. |
Personal injury or death can result from sudden machine movement. Sudden movement of the machine can cause injury to persons on or near the machine. To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before operating the machine. |
Personal injury can result from hydraulic oil pressure and hot oil. Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system. Make sure all of the attachments have been lowered, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand. |
Left Station
- Drive the machine to a smooth, horizontal surface.
- Move propel lever (3) to the NEUTRAL position.
Illustration 1 | g01473996 |
- Rotate speed dial (2) to the MINIMUM position.
- Move parking brake switch (1) to the ON position.
- Move screed lift switch (4) to the RAISE position. Completely lift the screed.
Illustration 2 | g01473997 |
- Engage screed lock mechanism (5) on both sides of the machine.
Illustration 3 | g01476878 |
- Move screed lift switch (4) to the FLOAT position. Allow the tow arms to rest on screed locks (6) .
Note: The screed lift switch on the inactive instrument panel must also be in the FLOAT position in order to lower the screed.
- Move screed lift switch (4) to the HOLD position.
- Move throttle control switch (6) to the LOW IDLE position. Hold the switch in this position for less than 1 second.
Illustration 4 | g01476881 |
- After the engine reaches low idle, move engine start switch (7) to the OFF position.
- Move engine start switch (7) to the ON position. Do not start the engine.
- Press home key (8) .
Illustration 5 | g01476895 |
- Press down key (9) until "Service" is highlighted on the display screen.
Illustration 6 | g01476902 |
- Press OK key (10) .
- Press down key (9) until "Calibrations" is highlighted on the display screen.
Illustration 7 | g01476954 |
- Press OK key (10) .
- Press down key (9) until "Lt Station Propel Lvr" is highlighted on the display screen.
Illustration 8 | g01476974 |
- Press OK key (10) .
- Press OK key (10) in order to begin the calibration.
- Move selector switch (11) on the operator station to the LEFT position.
Illustration 9 | g01476993 |
Illustration 10 | g01477015 |
- Press OK key (10) .
- Move propel lever (3) on the left instrument panel to the NEUTRAL position.
Illustration 11 | g01477016 |
- Press OK key (10) .
- The display should now read "CALIBRATION COMPLETE". Push back key (12) to return to calibration screen.
Illustration 12 | g01477094 |
- Push home key (8) in order to exit the calibration screen.
- Move engine start switch (7) to the OFF position.
Right Station
- Drive the machine to a smooth, horizontal surface.
- Move propel lever (3) to the NEUTRAL position.
Illustration 13 | g01473996 |
- Rotate speed dial (2) to the MINIMUM position.
- Move parking brake switch (1) to the ON position.
- Move screed lift switch (4) to the RAISE position. Completely lift the screed.
Illustration 14 | g01473997 |
- Engage screed lock mechanism (5) on both sides of the machine.
Illustration 15 | g01476878 |
- Move screed lift switch (4) to the FLOAT position. Allow the tow arms to rest on screed locks (6) .
Note: The screed lift switch on the inactive instrument panel must also be in the FLOAT position in order to lower the screed.
- Move screed lift switch (4) to the HOLD position.
- Move throttle control switch (6) to the LOW IDLE position. Hold the switch in this position for less than 1 second.
Illustration 16 | g01476881 |
- After the engine reaches low idle, move engine start switch (7) to the OFF position.
- Move engine start switch (7) to the ON position. Do not start the engine.
- Press home key (8) .
Illustration 17 | g01476895 |
- Press down key (9) until "Service" is highlighted on the display screen.
Illustration 18 | g01476902 |
- Press OK key (10) .
- Press down key (9) until "Calibrations" is highlighted on the display screen.
Illustration 19 | g01476954 |
- Press OK key (10) .
- Press down key (9) until "Rt Station Propel Lvr" is highlighted on the display screen.
Illustration 20 | g01477112 |
- Press OK key (10) .
- Press OK key (10) in order to begin the calibration.
- Move selector switch (11) on the operator station to the RIGHT position.
Illustration 21 | g01477115 |
Illustration 22 | g01477117 |
- Press OK key (10) .
- Move propel lever (12) on the right instrument panel to the NEUTRAL position.
Illustration 23 | g01477132 |
Illustration 24 | g01477134 |
- Press OK key (10) .
- The display should now read "CALIBRATION COMPLETE". Push back key (13) to return to calibration screen.
Illustration 25 | g01477136 |
- Push home key (8) in order to exit the calibration screen.
- Move the selector switch on the operator station to the LEFT position.
- Move engine start switch (7) to the OFF position.