Front Suspension (Cylinder) - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | -     | M30 x 3.5 导向螺柱     |
2     |
B     | 138-7576     | 连杆支架     | 1     |
C     | 138-7574     | 连杆支架     | 2     |
E     | 4C-5593     | 防粘结剂     | 1     |
F     | 6V-7030     | 千分尺深度表总成     | 1     |
- 将工具 (E) 涂敷在悬架油缸 (5) 的锥面上。 使用工具 (C) 和两台适当的起吊设备以将心轴 (4) 安装到悬架油缸 (5) 上。 心轴 (4) 的重量约为 1005 kg (2216 lb)。
Show/hide table
图 1 | g01415661 |
- 安装支架组件 (7) 。 安装螺栓 (6) 。 对另一侧的心轴 (4) 重复此步骤。
Show/hide table
图 2 | g01415684 |
- 将工具 (C) 从心轴 (4) 上拆下。
Show/hide table
图 3 | g01415352 |
- 使用工具 (B) 和适当的起吊设备将护圈盘 (2) 安装到工具 (A) 上。 护圈盘 (2) 的重量约为 110 kg (243 lb)。
Show/hide table
图 4 | g01415760 |
- 安装三根螺栓 (1) ,彼此间隔 120 度。 拆下工具 (B) 。 拧紧螺栓 (1) 至 203 ± 27 N·m (150 ± 20 lb ft) 的扭矩。 使用工具 (F) 以便测量支柱和护圈盘 (2) 之间的间隙。
- 松开螺栓 (1) 。 将工具 (B) 和适当的起吊设备连接到护圈盘 (2) 上。 护圈盘 (2) 的重量约为 110 kg (243 lb)。 拆下螺栓 (1) 。 将护圈盘 (2) 从工具 (A) 上拆下。
Show/hide table
图 5 | g01415760 |
- 安装垫片组 (3) ,其厚度必须等于步骤 5 中获得的测量值减去 8.6 ± 0.03 mm (0.3386 ± 0.0012 in)。 垫片组 (3) 的厚度不得小于 0.64 mm (0.025 in)。
Show/hide table
图 6 | g01415350 |
- 使用工具 (B) 和适当的起吊设备以安装护圈盘 (2) 。 护圈盘 (2) 的重量约为 110 kg (243 lb)。 安装三根螺栓 (1) 。 拆下工具 (B) 。 拆下工具 (A) 。
Show/hide table
图 7 | g01415760 |
- 安装其余的螺栓 (1) 。 拧紧螺栓 (1) 至 1800 ± 200 N·m (1328 ± 148
lb ft) 的扭矩。
注: 垫片组与护圈盘之间的预期间隙为 0.00 to 0.13 mm (0.000 to 0.005 in)。
Show/hide table
图 8 | g01415257 |
End By: 安装行车制动器和停车制动器。 请参阅 拆解和组装, "行车和停车制动器(前)- 安装"。
Caterpillar Information System:
793C Off-Highway Truck Machine Systems Front Suspension (Cylinder) - Remove
793D Off-Highway Truck/Tractor Service and Parking Brake (Front) - Assemble
793D Off-Highway Truck/Tractor Service and Parking Brake (Front) - Disassemble
793D Off-Highway Truck/Tractor Service and Parking Brake (Front) - Install
793D Off-Highway Truck/Tractor Service and Parking Brake (Front) - Remove
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Ride Control Accumulator - Test and Charge
3176C Engine for the R1600G and the R1700G Load Haul Dumps Speed Control (Remote Throttle) - Test
3176C Engine for the R1600G and the R1700G Load Haul Dumps Power Is Intermittently Low or Power Cutout Is Intermittent
3176C Engine for the R1600G and the R1700G Load Haul Dumps Oil Pressure Is Low
140H and 160H Motor Graders Changing Direction and Speed
2007/09/24 An Improved Fuse and ARC Suppressor is Now Used in the Axle Oil Cooler Wiring Harness {1365, 1408}
R1600G Load Haul Dump Machine Systems Tilt Lever and Tilt Link - Install
793D Off-Highway Truck/Tractor Front Suspension (Cylinder) - Remove
793D Off-Highway Truck/Tractor Front Suspension (Cylinder) - Install
160M Motor Grader Machine Systems Steering Cylinder - Remove and Install
140M Motor Grader Engine Supplement Water Temperature Regulator - Remove and Install
CP76 and CS76 Vibratory Compactors Propel System Case Drain Flow for Piston Motor (Drum Propel) - Test
2007/08/27 New AccuGrade ® Software is Now Available {7220, 7620}
CS54 and CP54 Vibratory Soil Compactors Fuel System Secondary Filter - Replace
CP76 and CS76 Vibratory Compactors Propel System Case Drain Flow for Piston Motor (Axle Propel) - Test
CS54 and CP54 Vibratory Soil Compactors Fuel System Primary Filter - Clean/Inspect/Replace
3508B Engine for Caterpillar Built Machines Turbocharger
2007/08/27 The Traction Control System (If Equipped) is Updated {1408, 4801}
CS56, CS64, CS74, CS76, CP56, CP64, CP74 and CP76 Vibratory Soil Compactors Fuel System Primary Filter (Water Separator) - Replace