Front Suspension (Cylinder) - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | -     |     | 2     |
B     | 138-7576     | 连杆支架     | 1     |
D     | 138-7574     | 连杆支架     | 2     |
E     | 4C-5593     | 防粘结剂     | 1     |
F     | 6V-7030     | 千分尺深度表总成     | 1     |
G     |     | 定位工具     | 1     |
- () () () () ()
Show/hide table
图 1 | g01414384 |
Show/hide table
图 2 | g01414235 |
- 安装螺栓 (7) 。 对机器的另一侧重复此步骤。
Show/hide table
图 3 | g01414468 |
- ()
- 安装工具 (A) 。
- () () () 转向阀 (1) 的重量约为 309 kg (681 lb)。 () 拆下工具 (B) 。 拧紧锁定螺栓 3 至扭矩为 203 ± 27 N·m 150 ± 20 lb ft 。 () () () 松开三个螺栓 3 。 () 拆下三条螺栓 (3) 。 拆下摇臂 1 。
Show/hide table
图 4 | g01414475 |
Show/hide table
图 5 | g01414476 |
- () 5 () () ()
Show/hide table
图 6 | g01414050 |
- () () () 转向阀 (1) 的重量约为 309 kg (681 lb)。 安装螺栓 (3) 。 拆下工具 (B) 。 拧紧螺栓 (3) 至扭矩为 1800 ± 200 N·m (1328 ± 148 lb ft)。 拆下工具 (A) 。
注: ()
Show/hide table
图 7 | g01414481 |
Show/hide table
图 8 | g01414482 |
- 安装螺栓 (2) 。 用 800 ± 50 N·m (590 ± 37 lb ft) 的扭矩拧紧螺栓 (2) 。 通过额外转动 120 度拧紧螺栓 (2) 。
Show/hide table
图 9 | g01524255 |
End By: 安装后部行车制动器和停车制动器。 请参阅 解体和组装 停车制动器 - 安装 。
Caterpillar Information System:
793D Off-Highway Truck/Tractor Front Suspension (Cylinder) - Remove
793C Off-Highway Truck Machine Systems Front Suspension (Cylinder) - Install
793C Off-Highway Truck Machine Systems Front Suspension (Cylinder) - Remove
793D Off-Highway Truck/Tractor Service and Parking Brake (Front) - Assemble
793D Off-Highway Truck/Tractor Service and Parking Brake (Front) - Disassemble
793D Off-Highway Truck/Tractor Service and Parking Brake (Front) - Install
793D Off-Highway Truck/Tractor Service and Parking Brake (Front) - Remove
938H Wheel Loader and IT38H Integrated Toolcarrier Hydraulic System Ride Control Accumulator - Test and Charge
3176C Engine for the R1600G and the R1700G Load Haul Dumps Speed Control (Remote Throttle) - Test
3176C Engine for the R1600G and the R1700G Load Haul Dumps Power Is Intermittently Low or Power Cutout Is Intermittent
3176C Engine for the R1600G and the R1700G Load Haul Dumps Oil Pressure Is Low
140H and 160H Motor Graders Changing Direction and Speed
160M Motor Grader Machine Systems Steering Cylinder - Remove and Install
140M Motor Grader Engine Supplement Water Temperature Regulator - Remove and Install
CP76 and CS76 Vibratory Compactors Propel System Case Drain Flow for Piston Motor (Drum Propel) - Test
2007/08/27 New AccuGrade ® Software is Now Available {7220, 7620}
CS54 and CP54 Vibratory Soil Compactors Fuel System Secondary Filter - Replace
CP76 and CS76 Vibratory Compactors Propel System Case Drain Flow for Piston Motor (Axle Propel) - Test
CS54 and CP54 Vibratory Soil Compactors Fuel System Primary Filter - Clean/Inspect/Replace
3508B Engine for Caterpillar Built Machines Turbocharger
2007/08/27 The Traction Control System (If Equipped) is Updated {1408, 4801}
CS56, CS64, CS74, CS76, CP56, CP64, CP74 and CP76 Vibratory Soil Compactors Fuel System Primary Filter (Water Separator) - Replace
CS56, CS64, CS74, CS76, CP56, CP64, CP74 and CP76 Vibratory Soil Compactors Isolation Mounts - Inspect/Replace
CP76 and CS76 Vibratory Compactors Propel System Travel Speed - Check