Transfer Gears - Assemble
组装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
B     | 1P-0510     | 起子总成     | 1     |
D     | 8T-5096     | 千分表总成     | 1     |
6V-6042 | 点群     | 1     | |
E     | 7M-7260     | 液体密封垫     | 1     |
- 检查所有 O 形密封圈和部件有无磨损或损坏。 如有必要,请更换部件。
- 利用所密封的润滑剂轻轻润滑所有 O 形密封圈。
- 冷却轴承外圈 (18) 。 将轴承外圈 (18) 安装到分动器壳体中。
Show/hide table
图 1 | g00575648 |
- 加热轴承内圈 (17) 。 将轴承内圈 (17) 安装到分动器 (16) 上。
Show/hide table
图 2 | g00575858 |
- 将分动器 (16) 定位到分动器壳体中。
- 冷却轴承外圈 (14) 。 将轴承外圈 (14) 装入轴承保持架 (13) 中。
Show/hide table
图 3 | g00575510 |
- 将原有垫片 (15) 和轴承保持架 (13) 安装到分动器壳体上。 安装将轴承保持架 (13) 固定在分动器壳体上的螺栓和垫圈。 拧紧螺栓至扭矩为 50 ± 10 N·m (37 ± 7 lb ft)。
Show/hide table
图 4 | g01409019 |
- 利用工具 (D) 测量轴承内圈 (17) 的轴向间隙。 增加或减少轴承保持架 (13) 与分动器壳体之间的垫片,以便使轴向间隙测量值达到 0.15 ± 0.05 mm (0.006 ± 0.002 in)。
- 将管组件 (10) 定位到分动器壳体上后连接管组件 (10) 。
Show/hide table
图 5 | g00575503 |
- 安装将管组件 (10) 固定在分动器壳体上的螺栓 (11) 。 将夹子 (12) 朝与螺栓 (11) 头部相反的方向弯曲。
- 加热轴承内圈 (9) 。 将两个滚柱轴承内圈 (9) 安装到分动器 (8) 上。
Show/hide table
图 6 | g00575871 |
- 将分动器 (8) 安装到分动器壳体上。
Show/hide table
图 7 | g00575498 |
- 将工具 (E) 涂抹到分动器壳体的密封孔内,并使工具干燥。
注: 不要将工具 (E) 涂抹到唇形密封上。
Show/hide table
图 8 | g01409027 |
Show/hide table
图 9 | g00575496 |
- 利用工具 (B) 将唇形密封 (6) 安装到轴承保持架 (3) 上。 用润滑剂稍微润滑要密封的唇形密封的密封唇。
- 冷却轴承外圈 (5) 。 将轴承外圈 (5) 安装到轴承保持架 (3) 上。
- 将 O 形密封圈 (7) 安装到轴承保持架 (3) 上。
- 用润滑剂稍微润滑要密封的分动器壳体的孔。 将原有垫片和轴承保持架 (3) 安装到分动器壳体上。 安装将轴承保持架 (3) 固定在分动器壳体上的螺栓 (1) 、垫圈和隔套。 拧紧螺栓 (1) 至扭矩为 50 ± 10 N·m (37 ± 7 lb ft)。
Show/hide table
图 10 | g00575894 |
Show/hide table
图 11 | g00575403 |
- 利用工具 (A) 测量轴承内圈 (9) 的轴向间隙。 增加或减少轴承保持架 (3) 与分动器壳体之间的垫片,以便使轴向间隙测量值达到 0.15 ± 0.05 mm (0.006 ± 0.002 in)。
- 将轭 (2) 安装到分动器上。
End By: 连接变速箱行星齿轮和分动器。 请参阅 拆解和组装, "变速箱行星齿轮和分动器 - 连接"。
Caterpillar Information System:
770 and 772 Off-Highway Trucks Power Train Transfer Gears - Disassemble
CP76 and CS76 Vibratory Compactors Propel System Relief Valve (Charge Pressure, Axle Propel Pump) - Test and Adjust
3176C Engine for the R1600G and the R1700G Load Haul Dumps Shutdown - Test
CP76 and CS76 Vibratory Compactors Propel System Relief Valve (Charge Pressure, Drum Propel Pump) - Test and Adjust
R1600G Load Haul Dump Fire Suppression System - Check - If Equipped
CS54 and CP54 Vibratory Soil Compactors Lubricant Viscosities
140M Motor Grader Engine Supplement Refrigerant Compressor - Remove and Install
CP54 and CS54 Vibratory Soil Compactors Machine Systems Cab Door
CP76 and CS76 Vibratory Compactors Machine Systems Piston Motor (Vibratory) - Test - Cooling Valve
CP56, CP64, CP74, CS56, CS64 and CS74 Paving Compactors Machine Systems Axle Housing (Parking Brake, Differential and Bevel Gear) - Assemble
CP56, CP64, CP74, CS56, CS64 and CS74 Paving Compactors Machine Systems Axle Housing (Parking Brake, Differential and Bevel Gear) - Disassemble
CP54 and CS54 Vibratory Soil Compactors Machine Systems Seat Belt
CP76 and CS76 Vibratory Compactors Propel System Relief Valve (Main, Drum Propel Pump) - Test and Adjust
3500B Engines and 776D, 777D, 784C, 785C, 789C, 793C and 793D Off-Highway Truck/Tractors Turbocharger
143H and 163H Motor Graders Wheel Bearing Oil Sample (Front) - Obtain - If Equipped
CS54 and CP54 Vibratory Soil Compactors Engine Air Filter Primary Element - Clean/Replace
2007/09/17 Additional Parts are Available for the Filler Cap {3177, 4332, 5056}
770 and 772 Off-Highway Trucks Power Train Transmission Hydraulic Control - Remove
3176C Engine for Caterpillar Built Machines Injector Solenoid - Test
770 and 772 Off-Highway Trucks Power Train Transmission Hydraulic Control - Install
770 and 772 Off-Highway Trucks Power Train Transmission Hydraulic Control - Disassemble
770 and 772 Off-Highway Trucks Power Train Transmission Hydraulic Control - Assemble
Wiring the 9X-9591 Electrical Converter Gp (PULSE WIDTH MODULATED){1421, 1901, 7490} Wiring the 9X-9591 Electrical Converter Gp (PULSE WIDTH MODULATED){1421, 1901, 7490}
3524B and C175 Engines for Off-Highway Truck/Tractors Turbocharger