Axle Housing (Parking Brake, Differential and Bevel Gear) - Assemble
组装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 202-7965     | 扳手套筒     | 1     |
C     | 1P-1859     | 挡圈钳     | 1     |
D     | 263-2152     | 花键扳手     | 1     |
E     | 263-2153     | 活动扳手     | 1     |
G     | 1P-0520     | 冲头总成     | 1     |
H     | 263-2154     | 有故障的小齿轮     | 1     |
J     | 235-2792     | 有故障的差速器     | 1     |
K     | 6V-2012     | 深度千分尺     | 1     |
L     | 8T-5096     | 千分表总成     | 1     |
M     | -     | Loctite 270     | 1     |
N     | -     | Loctite 518     | 1     |
P     | 8T-5096     | 千分表总成     | 1     |
R     | 441-3596     | 小齿轮螺母工具组件     | 1     |
- 使用工具 (G) 将轴承外圈 (43) 安装到中央壳体。
Show/hide table
图 1 | g01408949 |
- 安装轴承内圈 (41) 和 (42) 。 安装工具 (H) 。
Show/hide table
图 2 | g01075948 |
- 对齐拆卸步骤期间做的定位标记。 定位制动油缸 (1) ,临时安装螺栓 (2) 。 对另一侧重复上述步骤。
Show/hide table
图 3 | g01075951 |
- 将工具 (J) 安装到中央壳体中。 确保将工具 (J) 插入两个制动油缸中。
Show/hide table
图 4 | g01075953 |
- 使用工具 (K) 测量距离 (A) 。 距离 (B) 等于 130 mm (5.118 in)。 距离 (C) 等于 50 mm (1.969 in)。 使用下列方程式计算测量值 (X) :A mm + C mm - B mm = X mm。 记录测量值 (X) 。
Show/hide table
图 5 | g01075955 |
Show/hide table
图 6 | g01075956 |
- 测量值 (V) 压印在小齿轮轴 (38) 的顶部。 使用下来方程式计算测量值 (S) :X mm - V mm = S mm。
Show/hide table
图 7 | g01075959 |
- 根据可用的垫片列表,选择测量值 (S) 厚度的垫片。
- 拆下工具 (J) 。 卸下螺栓 (2) 和制动油缸 (1) 。 从工具 (H) 上拆下螺母、垫圈和隔套。 拆下工具 (H) 。 拆下轴承内圈 (41) 和 (42) 。
Show/hide table
图 8 | g01075961 |
- 将适当的垫片安装到小齿轮轴 (38) 上。 在斜面对着齿轮的情况下安装垫片。 加热轴承内圈 (42) 后将轴承内圈 (42) 安装到小齿轮轴 (38) 上。
Show/hide table
图 9 | g01076033 |
- 将垫圈 (39) 和可伸缩的隔套 (40) 安装到小齿轮轴 (38) 上。
Show/hide table
图 10 | g01076037 |
- 将小齿轮轴 (38) 安装到中央壳体中。 加热轴承内圈 (41) 后将轴承内圈 (41) 安装到小齿轮轴 (38) 上。
Show/hide table
图 11 | g01076039 |
- 安装隔套 (37) 、垫圈 (36) 和锁紧螺母 (35) 。 使用工具 (D) 和工具 (E) 拧紧锁紧螺母 (35) 。
Show/hide table
图 12 | g01074255 |
- 使用工具 (D) 和 (E) 及表盘式扭矩扳手以设定转矩。 拧紧螺母 (35) 以获得 4.0 至 4.4 N·m (36.0 至 39.0 lb in) 的转矩。
- 使用适当的锤子和冲头定位螺母 (35) 。
Show/hide table
图 13 | g01076414 |
- 安装隔套 (34) 。 使用工具 (C) 并安装挡圈 (33) 。
Show/hide table
图 14 | g01074252 |
注: 仅配备有车速表的机器上装有挡圈 (33) 和隔套 (34) 。
- 如果拆解期间拆下了衬套 (32) ,则安装衬套 (32) 。
Show/hide table
图 15 | g01074218 |
- 如果拆解期间拆下了衬套 (31) ,则安装衬套 (31) 。
Show/hide table
图 16 | g01074217 |
- 安装板 (30) 和盘 (29) 。 安装侧齿轮 (28) 。
Show/hide table
图 17 | g01074168 |
- 安装止推垫圈 (26) 和齿轮 (27) 。 安装轴 (25) 。 安装锁销 (24) 。
Show/hide table
图 18 | g01074165 |
- 安装侧齿轮 (23) 。 安装盘 (22) 和板 (21) 。 安装盖 (20) 。
Show/hide table
图 19 | g01074163 |
- 加热轴承内圈 (16) 和 (17) 。 安装轴承内圈 (16) 和 (17) 。
Show/hide table
图 20 | g01076415 |
- 将伞齿轮 (19) 安装到差速器上。 将工具 (M) 涂抹在螺栓 (18) 的螺纹上。 安装螺栓 (18) ,拧紧螺栓 (18) 至扭矩为 180 N·m (133 lb ft)。
Show/hide table
图 21 | g01074116 |
- 将套筒 (3) 安装到中央壳体中。
Show/hide table
图 22 | g01076707 |
- 将制动油缸 (1) 放置在平整表面上。 使用工具 (G) 并安装轴承外圈 (15) 。
注: 如果车桥配备有制动器,则使用步骤 24 至 28。
Show/hide table
图 23 | g01076712 |
- 使用工具 (A) 并安装扳手螺母 (14) 。
Show/hide table
图 24 | g01076744 |
- 将 O 型密封圈 (9) 和 (11) 安装到驱动销 (10) 上。 将驱动销 (10) 安装到活塞 (5) 中。 安装螺塞 (8) 。 在 O 形密封圈 (9) 和 (11) 上涂抹一薄层润滑脂。
Show/hide table
图 25 | g01074096 |
注: 检查 O 形密封圈有无磨损或损坏。 如有必要,更换O形密封圈。
- 在 O 形密封圈 (6) 和 (7) 上涂抹一薄层润滑脂。 安装 O 形密封圈 (6) 和 (7) 。 将活塞 (5) 安装到制动油缸 (1) 中。 安装锥形垫圈 (4) 。
Show/hide table
图 26 | g01076777 |
注: 检查 O 形密封圈有无磨损或损坏。 如有必要,更换O形密封圈。
- 将工具 (N) 涂抹到中央壳体和右制动油缸 (1) 的配合面上。 对齐拆卸步骤期间做的定位标记。 将制动油缸 (1) 定位到中央壳体上,然后安装螺栓 (2) 。 拧紧螺栓 (2) 至扭矩为 79 N·m (58 lb ft)。
Show/hide table
图 27 | g01076750 |
- 将差速器安装到中央壳体的左侧中。
Show/hide table
图 28 | g01076754 |
- 将工具 (N) 涂抹到中央壳体和左制动油缸 (1) 的配合面上。 对齐拆卸步骤期间做的定位标记。 将制动油缸 (1) 定位到中央壳体上,然后安装螺栓 (2) 。 拧紧螺栓 (2) 至扭矩为 79 N·m (58 lb ft)。
Show/hide table
图 29 | g01074031 |
- 摆动小齿轮轴,然后使用工具 (A) 拧紧扳手螺母,直到有少量齿隙,并且没有端隙。
- 将表盘式扭矩扳手安装到小齿轮轴上。 测量总扭矩。 使用以下公式计算总扭矩(TRT):P 为步骤 13 中测量的转矩。 TRT = P + 4.43 N·m (39.0 lb in) 至 P + 4.98 N·m (44.0 lb in).
- 如果总扭矩(TRT)小于规定的量,等量拧紧两个扳手螺母。 如果总扭矩(TRT)大于规定的量,等量松开两个扳手螺母。 务必保持微小的齿隙。
- 如图所示,使用工具 (R) ,将工具 (P) 安装到中央壳体上。 测量小齿轮和伞齿轮之间的齿隙。 正确的齿隙设定值为 0.180 至 0.230 mm (0.0071 至 0.0091 in)。
Show/hide table
图 30 | g03386391 |
- 如果齿隙不在规定范围内,拧松一个扳手螺母后等量拧紧相对的扳手螺母。 如果齿隙低于规定的值,朝方向 (A) 移动伞齿轮。 如果齿隙大于规定的值,朝方向 (B) 移动伞齿轮。
Show/hide table
图 31 | g01029595 |
- 将护圈 (13) 和螺栓 (12) 安装到两个制动油缸 (1) 中。 拧紧螺栓 (12) 至扭矩为 13 N·m (10 lb ft)。
Show/hide table
图 32 | g01076798 |
End By: 安装轮轴壳体、轮轴的轴和车轮法兰。 请参阅 拆解和组装, "轮轴壳体、轮轴的轴和车轮法兰 - 安装"。
Caterpillar Information System:
CP56, CP64, CP74, CS56, CS64 and CS74 Paving Compactors Machine Systems Axle Housing (Parking Brake, Differential and Bevel Gear) - Disassemble
CP54 and CS54 Vibratory Soil Compactors Machine Systems Seat Belt
140M Motor Grader Engine Supplement Refrigerant Condenser - Remove and Install
14M and 16M Motor Graders Machine Systems Lubrication System
3176C Engine for the R1600G and the R1700G Load Haul Dumps Speed/Timing - Test
CP54 and CS54 Vibratory Soil Compactors Machine Systems Engine Service Group
CS54 and CP54 Vibratory Soil Compactors Engine and Machine Warm-Up
CP76 and CS76 Vibratory Compactors Machine Systems Gear Pump Flow (Cooling Fan) - Test
2007/08/27 Changes to Testing and Adjusting, RENR4897, "216B, 226B, 232B, and 242B Skid Steer Loaders Machine Systems" , "Worksheets - Troubleshoot" {4350, 5050}
CP76 and CS76 Vibratory Compactors Machine Systems Case Drain Flow for Piston Motor (Vibratory) - Test
2007/08/27 Changes to Testing and Adjusting, RENR4897, "216B, 226B, 232B, and 242B Skid Steer Loaders Machine Systems" , "Line Relief Valve - Test and Adjust" {5117, 5117}
2007/08/27 Changes to Testing and Adjusting, RENR4897, "216B, 226B, 232B, and 242B Skid Steer Loaders Machine Systems" , "Main Relief Valve - Test and Adjust" {5069, 5069}
CP76 and CS76 Vibratory Compactors Machine Systems Piston Motor (Vibratory) - Test - Cooling Valve
CP54 and CS54 Vibratory Soil Compactors Machine Systems Cab Door
140M Motor Grader Engine Supplement Refrigerant Compressor - Remove and Install
CS54 and CP54 Vibratory Soil Compactors Lubricant Viscosities
R1600G Load Haul Dump Fire Suppression System - Check - If Equipped
CP76 and CS76 Vibratory Compactors Propel System Relief Valve (Charge Pressure, Drum Propel Pump) - Test and Adjust
3176C Engine for the R1600G and the R1700G Load Haul Dumps Shutdown - Test
CP76 and CS76 Vibratory Compactors Propel System Relief Valve (Charge Pressure, Axle Propel Pump) - Test and Adjust
770 and 772 Off-Highway Trucks Power Train Transfer Gears - Disassemble
770 and 772 Off-Highway Trucks Power Train Transfer Gears - Assemble
CP76 and CS76 Vibratory Compactors Propel System Relief Valve (Main, Drum Propel Pump) - Test and Adjust
3500B Engines and 776D, 777D, 784C, 785C, 789C, 793C and 793D Off-Highway Truck/Tractors Turbocharger