Water Pump - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | -     | 导向螺柱 (M8 × 70 mm)     |
2     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
- 确保水泵清洁且无磨损或损坏。 如有必要,更换水泵。
- 如有必要,将盖 (6) 安装到水泵 (3) 上。 遵循步骤 2.a 至 2.d,安装盖。
- 清洁盖 (6) 的配合面。
- 将新接头 (5) 安置在水泵 (3) 上。
- 将盖 (6) 安装到水泵 (3) 上。
- 将螺栓 (7) 安装到盖 (6) 上。 用手拧紧螺栓。
Show/hide table
图 1 | g01336659 |
- 清洁前盖 (1) 的配合面。
- 将工具 (A) 安装到位置 (X) 中。
Show/hide table
图 2 | g01336660 |
- 使用工具 (A) 对准新接头 (2) 与前盖 (1) 。 将接头安装到前盖上。
- 对准水泵 (3) 与工具 (A) 。 将水泵安装到前盖 (1) 上。
注: 确保水泵的齿轮与喷油泵的齿轮相啮合。
- 安装螺栓 (4) 。 请参阅插图 1。 用手拧紧螺栓。
注: 确保所有不同长度的螺栓安装位置正确。
- 拆下工具 (A) ,并安装剩余螺栓 (4) 。
- 按照图 3 所示的顺序拧紧螺栓 (4) 和 (7) 至扭矩为 22 N·m (16 lb ft)。
Show/hide table
图 3 | g01336661 |
- 将软管安装到水泵进口。 上紧软管卡箍。
- 向冷却系统加注冷却液。 有关正确的步骤,请参阅操作和保养手册, "冷却系统冷却液 - 更换"。
End By: 安装风扇和风扇皮带轮。 请参阅 拆解和组装, "风扇 - 拆卸和安装"。
Caterpillar Information System:
C6.6 Engines for Caterpillar Built Machines Water Pump - Remove
C6.6 Engines for Caterpillar Built Machines Engine Oil Pump - Install
C6.6 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
C6.6 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
C6.6 Engines for Caterpillar Built Machines Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
EquipmentManager Dealer Administrator Manual Major Repair
C6.6 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines Engine Oil Filter Base - Remove and Install
C6.6 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C6.6 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C6.6 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C6.6 Engines for Caterpillar Built Machines Flywheel - Remove
24M Motor Grader Power Train Electronic Control System MID 027 - CID 0379 - FMI 03
C6.6 Engines for Caterpillar Built Machines Flywheel - Install
C6.6 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove
C6.6 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
C6.6 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install - Standard Housing
C6.6 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install - Wet Back End Housing
C6.6 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove - Pulley with Split Lock Rings
C6.6 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Install - Pulleys without Split Lock Rings
C6.6 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Install - Pulley with Split Lock Rings
C6.6 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove - Pulleys without Split Lock Rings