Crankshaft Rear Seal - Remove
拆卸步骤
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 194-3536 | T40 Torx 套筒 | 1 |
| B | 227-4389 | E10 Torx 套筒 | 1 |
开始:
- 拆下飞轮壳体。 有关正确步骤，请参阅拆解和组装, "飞轮壳 - 拆卸和安装"。
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
| 注意 |
|---|
在检验、保养、测试、调整及维修产品时，务必留心，确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前，要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
Show/hide table
 | |
| 图 1 | g01337506 |
典型示例 | |
- 使用工具 (B) 将 torx 螺栓 (1) 从曲轴后密封组件 (2) 上拆下。
注: 曲轴后密封组件不可维修。 如果拆下了曲轴后密封组件，必须更换该组件。
- 使用工具 (A) 将 torx 螺栓 (3) 从曲轴后密封组件上拆下。
- 从缸体上拆下曲轴后密封组件 (2) 。 废弃曲轴后密封组件 (2) 。
注: 不需要拆卸发动机油底壳护板，便可拆下曲轴后密封。
Caterpillar Information System:
C6.6 Engines for Caterpillar Built Machines Flywheel - Install
24M Motor Grader Power Train Electronic Control System MID 027 - CID 0379 - FMI 03
C6.6 Engines for Caterpillar Built Machines Flywheel - Remove
C6.6 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C6.6 Engines for Caterpillar Built Machines Water Pump - Install
C6.6 Engines for Caterpillar Built Machines Water Pump - Remove
C6.6 Engines for Caterpillar Built Machines Engine Oil Pump - Install
C6.6 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
C6.6 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
C6.6 Engines for Caterpillar Built Machines Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
EquipmentManager Dealer Administrator Manual Major Repair
C6.6 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
C6.6 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install - Standard Housing
C6.6 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install - Wet Back End Housing
C6.6 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove - Pulley with Split Lock Rings
C6.6 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Install - Pulleys without Split Lock Rings
C6.6 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Install - Pulley with Split Lock Rings
C6.6 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove - Pulleys without Split Lock Rings
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train Track Drive - Disassemble
C6.6 Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove and Install
2007/07/09 New Caterpiller Monitor Software is Now Available {7490, 7620}
770 and 772 Off-Highway Truck/Tractors Evaporator Coil - Remove and Install
C6.6 Engines for Caterpillar Built Machines Front Cover - Remove and Install