Water Temperature Regulator - Remove and Install
拆卸步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
- 将冷却液从冷却系统中排入适当的容器至液位低于水温调节器,以便保存或废弃这些冷却液。 有关正确的排放步骤,请参阅操作和保养手册, "冷却系统冷却液 - 更换"。
- 松开上部散热器软管上的软管卡箍,将上部散热器软管从水温调节器壳体 (2) 上断开。
- 从水温调节器壳体 (2) 上卸下螺栓 (1) 。
Show/hide table
图 1 | g01336665 |
典型实例 |
- 将水温调节器壳体 (2) 从缸盖上卸下。
注: 记录水温调节器壳体的朝向。
- 将 O 形密封圈 (3) 从水温调节器壳体 (2) 上卸下。
Show/hide table
图 2 | g01336667 |
典型实例 |
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保水温调节器壳体 (2) 的所有部件清洁且无磨损或损坏。 检查水温调节器是否正常工作。 请参阅系统操作、测试和调整, "水温调节器 - 测试",以了解测试水温调节器的程序。 如果水温调节器的任何部件磨损或损坏,必须更换整个组件。
- 如果安装原来的水温调节器,将一个新 O 形密封圈 (3) 安置到水温调节器壳体 (2) 的凹槽中。
提供的新水温调节器壳体配有一个新 O 形密封圈。
Show/hide table
图 3 | g01336667 |
典型实例 |
- 将水温调节器壳体 (2) 安装到缸盖上。
注: 确保水温调节器壳体的朝向正确。
- 安装螺栓 (1) 。 拧紧螺栓 (1) 至扭矩为 44 N·m (32.5 lb ft)。
Show/hide table
图 4 | g01336665 |
典型实例 |
- 连接上部散热器软管,拧紧软管卡箍。
- 加注冷却系统至正确液位。 请参阅操作和保养手册, "冷却系统冷却液 - 检查"和操作和保养手册, "冷却系统冷却液 - 更换"以了解正确的加注程序。
Caterpillar Information System:
C6.6 Engines for Caterpillar Built Machines Water Pump - Install
C6.6 Engines for Caterpillar Built Machines Water Pump - Remove
C6.6 Engines for Caterpillar Built Machines Engine Oil Pump - Install
C6.6 Engines for Caterpillar Built Machines Engine Oil Pump - Remove
C6.6 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install
C6.6 Engines for Caterpillar Built Machines Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
EquipmentManager Dealer Administrator Manual Major Repair
C6.6 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
C6.6 Engines for Caterpillar Built Machines Engine Oil Filter Base - Remove and Install
C6.6 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C6.6 Engines for Caterpillar Built Machines Flywheel - Remove
24M Motor Grader Power Train Electronic Control System MID 027 - CID 0379 - FMI 03
C6.6 Engines for Caterpillar Built Machines Flywheel - Install
C6.6 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove
C6.6 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
C6.6 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install - Standard Housing
C6.6 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install - Wet Back End Housing
C6.6 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove - Pulley with Split Lock Rings
C6.6 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Install - Pulleys without Split Lock Rings
C6.6 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Install - Pulley with Split Lock Rings
C6.6 Engines for Caterpillar Built Machines Vibration Damper and Pulley - Remove - Pulleys without Split Lock Rings
259B3 Compact Track Loader, 247B3 and 257B3 Multi Terrain Loaders and 216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders Power Train Track Drive - Disassemble