Wheel and Tire (Rear) - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 155-3597     | 止轮块     | 2     |
B     | 4C-5809     | 电动液压泵总成     | 2     |
9U-7540 | 起吊台架     | 2     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 连接转向机架锁。 请参阅操作和保养手册, "转向机架锁"。
- 使用工具 (A) 塞住前轮。
Show/hide table
图 1 | g01389301 |
- 利用工具 (B) 升高机器尾部,直到后轮离地。
Show/hide table
图 2 | g01389289 |
- 连接适当的起吊设备到后车轮和轮胎 (1) 上。 拆下螺栓 (2) 。 从主轴中心拆卸后车轮和轮胎 (1) 。 后车轮和轮胎 (1) 的重量约为 340 kg (750 lb)。 对其余车轮重复此步骤。
Show/hide table
图 3 | g01389302 |
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 155-3597     | 止轮块     | 2     |
B     | 4C-5809     | 电动液压泵总成     | 2     |
9U-7540 | 起吊台架     | 2     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用适当的起吊设备安装后轮和轮胎 (1) 。 后车轮和轮胎 (1) 的重量约为 340 kg (750 lb)。 安装螺栓 (2) 。 拧紧螺栓 (2) 至 1800 ± 200 N·m (1328 ± 148 lb ft) 的扭矩。 对其余车轮重复此步骤。
Show/hide table
图 4 | g01389302 |
- 利用工具 (B) 降下机器后部。 拆下工具 (B) 。
Show/hide table
图 5 | g01389289 |
- 分离转向机架锁。 请参阅操作和保养手册, "转向机架锁"。
- 将工具 (A) 从前轮上拆下。
Show/hide table
图 6 | g01389301 |
Caterpillar Information System:
24M Motor Grader Hydraulic and Steering System Pump Control Valve (Implement, Steering)
420E, 430E, 432E, 434E, 442E and 444E Backhoe Loaders Hydraulic and Steering System Bank Valve (Loader)
587R Pipelayer Power Train Transmission Hydraulic Control Valve - Remove
EquipmentManager Dealer Administrator Manual Enable Program
770 and 772 Off-Highway Truck/Tractors Metering Pump (Steering) - Remove and Install
0R-9393 Cylinder Pack Gp Piston Ring Position on Certain C16, 3406E, and 3456 Engines{1215, 1225} 0R-9393 Cylinder Pack Gp Piston Ring Position on Certain C16, 3406E, and 3456 Engines{1215, 1225}
584 and 584HD Forwarders Slope Operation
24M Motor Grader Hydraulic and Steering System Piston Pump (Implement and Steering)
AP655D and BG655D Asphalt Pavers Machine Systems General Information (Auxiliary Hydraulic System)
16M Motor Grader Machine Systems Piston Pump (Hydraulic Fan) - Assemble
EquipmentManager User Guide Getting Started
16M Motor Grader Machine Systems Piston Pump (Hydraulic Fan) - Disassemble
16M Motor Grader Power Train Drive Chain - Install
AccuGrade® Laser (CB420) Full Sensor - Calibrate
16M Motor Grader Power Train Drive Chain - Remove
AccuGrade® Laser (CB420) Module - Flash Program
587R Pipelayer Power Train Transmission Hydraulic Control Valve - Install
Problems with Bias Ply Tires on Specific Off-Highway Trucks{4203} Problems with Bias Ply Tires on Specific Off-Highway Trucks{4203}
541 Track Feller Buncher, 551 Track Feller Buncher and 552 Track Feller Buncher Machine Systems Pilot Hydraulic System
R1600G Load Haul Dump Cooling System Coolant Additive (DEAC) - Add
216B2, 226B2, 232B2, 236B2, 242B2 and 252B2 Skid Steer Loaders Stopping the Engine if an Electrical Malfunction Occurs
541 Track Feller Buncher, 551 Track Feller Buncher and 552 Track Feller Buncher Machine Systems Pump Flow - Test
Cleaning the Compression Brake{1129} Cleaning the Compression Brake{1129}
216B3, 226B3, 236B3, 242B3 and 252B3 Skid Steer Loaders, 247B3 and 257B3 Multi Terrain Loaders and 259B3 Compact Track Loader Plate Locations and Film Locations