Steering Column - Assemble
组装步骤
- 清洁并检查所有零件。 如果任何零件磨损或损坏,则应使用 Caterpillar 新件进行更换。
- 将接头组件 (16) 和接头组件 (20) 安装到轴 (19) 的两端。 安装螺母 (17) 和螺栓。 安装螺母 (18) 和螺栓。 将两个螺母拧紧至扭矩 30 ± 3 N·m (22 ± 2 lb ft)。
Show/hide table
图 1 | g00868310 |
- 将转向柱 (1) 放入适当的软口台钳中,如图所示。
Show/hide table
图 2 | g00868305 |
- 将接头组件 (16) 安装到转向柱 (1) 上。 安装螺母 (15) 和螺栓。 拧紧螺母至扭矩为 30 ± 3 N·m (22 ± 2 lb ft)。
- 将气体支撑 (9) 放置在转向柱 (1) 上。 安装螺母 (13) 、螺栓、螺母 (14) 和螺栓。 拧紧螺母至扭矩为 20 ± 3 N·m (15 ± 2 lb ft)。
Show/hide table
图 3 | g00868280 |
- 将转向柱 (1) 重新定位到软口台钳中,如图所示。 将倾斜杆套件 (12) 放置在转向柱上。 安装螺钉 (11) 。 拧紧螺钉 (11) ,使其扭矩达到 1.75 ± .15 N·m (15 ± 1.3 lb in)。
Show/hide table
图 4 | g00868290 |
- 将电缆 (8) 放置到拆解步骤中记下的位置上。 将电缆的末端放置在气体支撑 (9) 的固定件中。 请参阅图 5 中的黑色箭头。
Show/hide table
图 5 | g00868274 |
- 拉回气体支撑 (9) 上的臂,然后将电缆夹组件 (10) 固定到位。 请参阅图 5 中的白色箭头。
注: 向前拉倾斜杆时,确保转向柱将向两个方向倾斜。 释放倾斜杆后,确保转向柱锁定到位。 使用电缆夹组件 (10) 上的螺帽调整倾斜杆。
- 将花键在两个组件上排成一排后,把方向盘 (3) 安装到转向柱 (1) 上。 确保方向盘在转向柱上完全固定。
Show/hide table
图 6 | g00867920 |
- 安装螺母 (7) 将方向盘 (3) 固定到转向柱 (1) 上。 拧紧螺母至扭矩为 48 ± 5 N·m (35 ± 4 lb ft)。
- 将板 (6) 安装到方向盘 (3) 中心中。 请参阅图 8 以了解导线 (4) 的位置。
Show/hide table
图 7 | g00867908 |
Show/hide table
图 8 | g00867896 |
- 将弹簧 (5) 安装到方向盘的中心。 将导线 (4) 连接至喇叭组件 (2) 上。
- 将喇叭组件 (2) 安装到方向盘 (3) 中。
Show/hide table
图 9 | g00867879 |
- 从软口台钳上拆下转向柱 (1) 。
End By: 安装转向柱。 请参考 拆解和组装, "转向柱 - 安装"。
Caterpillar Information System:
770 and 772 Off-Highway Truck/Tractors Steering Column - Disassemble
CB14 Paving Compactor Machine Systems Spray Bar - Remove and Install
587R Pipelayer Power Train Torque Converter Outlet Relief Valve - Remove
2007/06/18 Managing Engine Oil Service Levels {1348}
24M Motor Grader Power Train Electronic Control System MID 027 - CID 1639 - FMI 02
770 and 772 Off-Highway Truck/Tractors Steering Column - Install
770 and 772 Off-Highway Truck/Tractors Steering Column - Remove
2007/06/18 Improved Sealing for Transmission Scavenge Pump Now Used {3115}
R1600G Load Haul Dump Reference Material
R1600G Load Haul Dump Before Operation (Remote Control)
R1600G Load Haul Dump Stopping the Machine
R1600G Load Haul Dump Machine Operation Information
770 and 772 Off-Highway Truck/Tractors Steering Cylinder - Remove and Install
24M Motor Grader Hydraulic and Steering System Disc Pack Preload for Circle Drive - Adjust
CS54 and CP54 Vibratory Soil Compactors Parking Brake - Check
587R Pipelayer Power Train Torque Converter Outlet Relief Valve - Install
EquipmentManager Dealer Administrator Manual Planned Maintenance
EquipmentManager User Guide General Information
12H, 140H, 143H, 160H and 163H Motor Graders Hydraulic and Steering System Position Sender (Articulation)
CB14 Paving Compactor Machine Systems Gerotor Motor (Drum Propel) - Remove
770 and 772 Off-Highway Truck/Tractors Center Arm (Steering) - Remove and Install
CB14 Paving Compactor Machine Systems Gerotor Motor (Drum Propel) - Install
CB14 Paving Compactor Machine Systems Gerotor Motor (Drum Propel) - Disassemble
CB14 Paving Compactor Machine Systems Gerotor Motor (Drum Propel) - Assemble