Operating Modes (Dual Sonic System)
Show/hide table
| 注意 |
|---|
如果铲刀上配备了 AccuGrade 标高传感器，则将回转盘和/或铲刀移动到最左端或最右端时必须小心谨慎。 将铲刀和/或回转盘移动到最左端或最右端时，可能会损坏传感器和/或与传感器连接的挠曲电缆线束。 |
显示器的 LCD 显示了与当前作业相关的具体信息。
选择的操作模式会影响制导模式下的屏幕外观。
制导模式
Show/hide table
 | |
| 图 1 | g01298924 |
用户界面 (1) 箭头键 (2) 液晶显示器 (LCD) (3) 标高选择键 (4) 增量/铲刀斜坡方向键 (5) 标高选择键 (6) 菜单键 (7) "Esc"左复位/左定准键 (8) "OK" 右复位/右定准键 (A) 坡度指示灯 | |
Show/hide table
 | |
| 图 2 | g01300764 |
(21) 左传感器位置窗口 (22) 右传感器位置窗口 (23) 设备状态图标 (24) 左标高显示图标 (25) 右标高显示图标 (26) 左制导源图标 (27) 右制导源图标 (28) 左基准标高 (29) 右基准标高 | |
将系统配置为双声波系统时，将出现与图 2 类似的屏幕。
- 选择独立操作模式。
- 操作 ST300 时，将 ST300 配置为左或右。 配置时请断开另一个 ST300。
- 通过声波操作将标高选择按钮切换到铲刀的一侧。
- 使用箭头键或遥控开关进入需要的横坡。
- 将横坡侧置于自动模式，以便将铲刀置于所需的坡度。
- 手动调整声波追踪器，使其垂直并处于基准面上方约 18 英寸左右的位置。
- 如果声波追踪器安装在左侧，按下左定准按钮对声波追踪器进行定准。 如果声波追踪器安装在右侧，按下右定准按钮对声波追踪器进行定准。
- 设置基准标高。
- 移动机器并将铲刀两侧均置于自动模式。
Caterpillar Information System:
AccuGrade® 2D (CD610) for 120K, 120M, 12K, 12M, 140K, 140M, 14M, 160K, 160M, 16M and 24M Motor Graders General Maintenance Information
AccuGrade® 2D (CD610) for 120K, 120M, 12K, 12M, 140K, 140M, 14M, 160K, 160M, 16M and 24M Motor Graders End User License Agreement
AccuGrade® 2D (CD610) for 120K, 120M, 12K, 12M, 140K, 140M, 14M, 160K, 160M, 16M and 24M Motor Graders Display Description (Single Sonic System)
AccuGrade® 2D (CD610) for 120K, 120M, 12K, 12M, 140K, 140M, 14M, 160K, 160M, 16M and 24M Motor Graders Display Description (Single Mast System)
AccuGrade® 2D (CD610) for 120K, 120M, 12K, 12M, 140K, 140M, 14M, 160K, 160M, 16M and 24M Motor Graders Display Description (Dual Sonic System)
AccuGrade® 2D (CD610) for 120K, 120M, 12K, 12M, 140K, 140M, 14M, 160K, 160M, 16M and 24M Motor Graders Display Description (Dual Mast System)
M325D and M330D Excavators Machine Electronic Control System Calibration
AccuGrade® 2D (CD610) for 120K, 120M, 12K, 12M, 140K, 140M, 14M, 160K, 160M, 16M and 24M Motor Graders Display Description (Cross Slope System)
AccuGrade® 2D (CD610) for 120K, 120M, 12K, 12M, 140K, 140M, 14M, 160K, 160M, 16M and 24M Motor Graders Configuration
TK711, TK721, TK722, TK732, TK741, TK751 and TK752 Track Feller Bunchers IQAN MDM Monitor Fault ; Event Codes Input High Error IQAN XT2 A0-33
2007/01/22 Air Cleaner Valve and Lines Group Are Available for Air Cleaner Assembly on Backhoe Loaders {1051}
TK711, TK721, TK722, TK732, TK741, TK751 and TK752 Track Feller Bunchers IQAN MDM Monitor Fault ; Event Codes Input High Error IQAN XT2 A0-31
AccuGrade® 2D (CD610) for 120K, 120M, 12K, 12M, 140K, 140M, 14M, 160K, 160M, 16M and 24M Motor Graders Setup (Dual Mast System)
793D Off-Highway Truck/Tractor Metering Pump (Steering) - Disassemble
793D Off-Highway Truck/Tractor Metering Pump (Steering) - Assemble
AccuGrade® 2D (CD610) for 120K, 120M, 12K, 12M, 140K, 140M, 14M, 160K, 160M, 16M and 24M Motor Graders Operating Modes (Dual Mast System)
AccuGrade® 2D (CD610) for 120K, 120M, 12K, 12M, 140K, 140M, 14M, 160K, 160M, 16M and 24M Motor Graders Shutdown (Dual Mast System)
AccuGrade® 2D (CD610) for 120K, 120M, 12K, 12M, 140K, 140M, 14M, 160K, 160M, 16M and 24M Motor Graders Startup (Dual Mast System)
AccuGrade® 2D (CD610) for 120K, 120M, 12K, 12M, 140K, 140M, 14M, 160K, 160M, 16M and 24M Motor Graders Operating Modes (Single Mast System with Single Sonic System)
AccuGrade® 2D (CD610) for 120K, 120M, 12K, 12M, 140K, 140M, 14M, 160K, 160M, 16M and 24M Motor Graders Startup (Single Mast System with Single Sonic System)
AccuGrade® 2D (CD610) for 120K, 120M, 12K, 12M, 140K, 140M, 14M, 160K, 160M, 16M and 24M Motor Graders Operating Modes (Single Mast System)
AccuGrade® 2D (CD610) for 120K, 120M, 12K, 12M, 140K, 140M, 14M, 160K, 160M, 16M and 24M Motor Graders Shutdown (Single Mast System)
AccuGrade® 2D (CD610) for 120K, 120M, 12K, 12M, 140K, 140M, 14M, 160K, 160M, 16M and 24M Motor Graders Startup (Single Mast System)
AccuGrade® 2D (CD610) for 120K, 120M, 12K, 12M, 140K, 140M, 14M, 160K, 160M, 16M and 24M Motor Graders Operating Modes (Single Sonic System)