Mixing Chamber - Install
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 1U-9201     | Lever Puller Hoist     | 1     |
B     | 137-4370     | Load Leveling Beam     | 1     |
C     | FT-2977     | Skid Plate     | 1     |
- Use Tool (C) in order to slide mixing chamber assembly (1) and the rotor under the machine.
- Attach Tooling (B) and a suitable lifting device to the mixing chamber. Lift the mixing chamber and the rotor and remove Tooling (C). The weight of the mixing chamber and the rotor is approximately 7940 kg (17500 lb).
Show/hide table
Illustration 1 | g01289531 |
- Install bolts (14) .
Show/hide table
Illustration 2 | g01289533 |
- Install drive shaft (14) and bolts (13) to differential (12) .
Show/hide table
Illustration 3 | g01294364 |
- Remove Tooling (A) and a suitable lifting sling from the mixing chamber and the rotor axle.
Show/hide table
Illustration 4 | g01286291 |
Note: A typical example
- Attach a suitable lifting device to the chain cases. Raise the chain cases and remove the suitable blocks between the chain cases and the mixing chamber. The weight of the chain cases and the rotor assembly is approximately 3950 kg (8700 lb).
- Install mixing chamber linkage (9), pin (11), and cotter pin (10) to both sides of the mixing chamber.
Show/hide table
Illustration 5 | g01286299 |
- Connect hose assemblies (7) to hydraulic cylinder (8) .
Show/hide table
Illustration 6 | g01286298 |
- Connect hose assemblies (5) to front hood door (6) .
Show/hide table
Illustration 7 | g01286295 |
- Install hydraulic cylinder (4), bolt (3), and nut (2) to mixing chamber (1) .
Show/hide table
Illustration 8 | g01286294 |
End By:
- Install the hydraulic cylinder (rotor lift). Refer to Disassembly and Assembly, "Hydraulic Cylinder (Rotor Lift) - Remove and Install".
- Install the rotor drive shaft. Refer to Disassembly and Assembly, "Rotor Drive Shaft - Remove and Install".
- Install the oil tank. Refer to Disassembly and Assembly, "Oil Tank (Rotor Drive Lubrication) - Remove and Install".
- Install the tire and rim (rear). Refer to Disassembly and Assembly, "Tire and Rim (Rear) - Remove and Install".
Caterpillar Information System:
RM-300 Reclaimer Mixer Machine Systems Mixing Chamber - Remove
RM-300 Reclaimer Mixer Machine Systems Oscillating and Steering Bar - Remove and Install
RM-300 Reclaimer Mixer Machine Systems Mixing Chamber Linkage - Remove and Install
RM-300 Reclaimer Mixer Machine Systems Hydraulic Cylinder (Rear Steering) - Remove and Install
14M and 16M Motor Graders Power Train Relief Valve - Drain (Clutch 7)
14M and 16M Motor Graders Power Train Relief Valve - Main Relief
14M and 16M Motor Graders Power Train Relief Valve - Transmission Gear Lube
Improvements to the Engine Compartment on Landfill Compactors{1000, 7000} Improvements to the Engine Compartment on Landfill Compactors{1000, 7000}
2006/07/10 Improved Grease Is Now Used in the Front Suspension Group {7200, 7201}
14M and 16M Motor Graders Power Train Modulating Valve (Transmission Hydraulic Control)
3176C Engines for Caterpillar Built Machines CID 0545 FMI 05 Ether Start Relay open/short to +batt
14M and 16M Motor Graders Power Train Relief Valve (Cooler Bypass)
RM-300 Reclaimer Mixer Machine Systems Torque Limiting Coupling - Remove
RM-300 Reclaimer Mixer Machine Systems Torque Limiting Coupling - Install
RM-300 Reclaimer Mixer Machine Systems Hydraulic Cylinder (Front Steering) - Remove and Install
793D Off-Highway Truck/Tractor Control Valve (Hoist) - Disassemble
793D Off-Highway Truck/Tractor Control Valve (Hoist) - Assemble
725, 730 and 730 EJECTOR Articulated Trucks Power Train General Troubleshooting Information
2006/08/21 New High Efficiency Oil Filters are Now Available {1308}
3176C Engines for Caterpillar Built Machines Event Codes
2006/07/03 Retention Is Improved on the Bolts on the Hoist Cylinders {0649, 5102, 6068, 7562}
D6K Track-Type Tractor Machine Systems Control Manifold (Hydraulic Fan) - Disassemble
Starting and Charging Systems Starter Solenoid (Starter Two) Test Description
725, 730 and 730 EJECTOR Articulated Trucks Power Train Transfer Gear Lubrication System