Hydraulic Tank - Assemble
组装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7575     | 连杆支架     | 2     |
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 请勿使用抹布擦干零件。 棉绒可能会留在零件上,从而引发故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。 尘土及其他污染物可能会损坏精密部件。 组装步骤应在清洁的工作面上进行。 务必盖上部件并采取适当保护措施。
- 将阀 (34) 、弹簧 (35) 、管 (36) 、法兰 (37) 和两个螺栓 (38) 安装至滤清器底座 (32) 。
Show/hide table
图 1 | g01090777 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 将七个 O 形密封圈 (33) 安装至滤清器底座 (32) 。
Show/hide table
图 2 | g01090775 |
- 安装两个滤清器底座 (32) 。 安装固定两个滤清器底座 (32) 的四个螺栓。
Show/hide table
图 3 | g01090772 |
- 将接头 (31) 和 O 形密封圈安装到吸油歧管 (29) 上。
Show/hide table
图 4 | g01090771 |
- 将 10 个 O 形密封圈 (30) 安装到吸油歧管 (29) 上。
- 安装吸油歧管 (29) 。 安装固定吸油歧管 (29) 的螺栓。
Show/hide table
图 5 | g01090770 |
- 将七个 O 形密封圈 (28) 安装至吸油体 (27) 。
Show/hide table
图 6 | g01090768 |
- 安装吸油体 (27) 。 安装固定吸油体 (27) 的四个螺栓。
Show/hide table
图 7 | g01090767 |
- 将 O 形密封圈 (23) 、阀 (24) 、弹簧 (25) 和导向器 (26) 安装到排放阀阀体 (20) 上。
Show/hide table
图 8 | g01090765 |
- 安装适配器 (22) 和 O 形密封圈。 安装两个螺母 (21) 。
Show/hide table
图 9 | g01091149 |
液压油箱排放阀组件 |
- 安装排放阀阀体 (20) 。 安装两个螺栓 (19) 。
- 将两个 O 形密封圈 (15) 、板 (16) 、玻璃 (17) 和护环 (18) 安装到目测表 (14) 上。
Show/hide table
图 10 | g01090766 |
- 安装目测表 (14) 。
Show/hide table
图 11 | g01090764 |
- 安装两个螺栓 (13) 。 拧紧两个螺栓 (13) 至扭矩为 30 ± 7 N·m (23 ± 5 lb ft)。
- 安装密封 (39) 前,清洁密封表面。
Show/hide table
图 12 | g01091156 |
- 安装密封 (39) 。 交叠密封 (39) 的端部以便完成密封。
- 将工具 (A) 和适当的起吊设备安装到盖 (11) 上。 盖 (11) 的重量约为 43 kg (95 lb)。
注: 油箱 (12) 的重量约为 59 kg (130 lb)。
Show/hide table
图 13 | g01090763 |
- 安装盖 (11) 。
- 安装 62 个螺栓 (10) 和锁紧螺母。
Show/hide table
图 14 | g01090762 |
- 将 O 形密封圈 (7) 安装到盖 (1) 上。
Show/hide table
图 15 | g01090761 |
- 安装锥形锁紧双头螺栓 (4) 。 拧紧锥形锁紧双头螺栓 (4) 至扭矩为 35 ± 5 N·m (26 ± 4 lb ft)。
- 安装滤芯 (3) 。
- 将 O 形密封圈 (8) 安装到挡圈 (5) 上。 安装挡圈 (5) 。
- 安装锁紧螺母 (9) 和垫圈 (6) 。 拧紧锁紧螺母 (9) 至扭矩为 10 ± 1.5 N·m (7 ± 1 lb ft)。
- 安装两个盖 (1) 。 安装八个螺母 (2) 。
Show/hide table
图 16 | g01090759 |
End By: 安装液压油箱。 请参阅 拆解和组装, "液压油箱 - 安装"。
Caterpillar Information System:
R2900G Load Haul Dump Machine Systems Diverter Valve (Secondary Steering) - Remove
446D Backhoe Loader Machine Systems Pilot Valve (Stabilizer) - Remove
CB-334E and CB-335E Paving Compactors Capacities (Refill)
CB-334E Series II and CB-335E Series II Paving Compactors Stopping the Machine
CB-334E Series II and CB-335E Series II Paving Compactors Engine Starting
416E Backhoe Loader Joystick Control (Loader)
CB-434D and CB-434D XW Vibratory Compactor Machine Systems Gear Pump (Steering) - Remove
446D Backhoe Loader Machine Systems Pilot Valve (Backhoe) - Assemble
CB-214E, CB-224E and CB-225E Vibratory Compactors Machine Systems Direction and Speed Control - Assemble
CB-434D and CB-434D XW Vibratory Compactor Machine Systems Direction and Speed Control - Remove and Install
CB-434D and CB-434D XW Vibratory Compactor Machine Systems Seat - Remove and Install
CB-214E, CB-224E and CB-225E Vibratory Compactors Machine Systems Additive Tank - Install
2004/08/02 Correction to Disassembly and Assembly , "Piston Pump (Brake) - Assemble" {4268, 5070}
2004/08/02 Correction to Disassembly and Assembly , "Piston Pump (Brake) - Assemble" {4268, 5070}
CB-434D and CB-434D XW Vibratory Compactor Machine Systems Operator Platform - Remove and Install
446D Backhoe Loader Machine Systems Pilot Valve (Stabilizer) - Install
AP-1000D, AP-1055D, AP-655C, BG-2255C, BG-2455D and BG-260D Asphalt Pavers Calibration Error Code List (Caterpillar Monitoring System)
C4.4 (Mech) Industrial Engine Battery - Replace
C4.4 (Mech) Industrial Engine Battery or Battery Cable - Disconnect
797 Off-Highway Truck Engine Components - Clean/Inspect, Rebuild/Install Reman, Install New - 797 LAA Machines Only
797 Off-Highway Truck Engine Components - Rebuild//Replace/Install Reman - 797 LAA Machines Only
CB-334E Series II and CB-335E Series II Paving Compactors Tire Inflation Pressure Adjustment
3508 EUI Engine for Off-Highway Truck/Tractors Water Pump
446D Backhoe Loader Machine Systems Pilot Valve (Stabilizer) - Disassemble