Removal Procedure
Show/hide table
Table 1
| Required Tools |
| Tool |
Part Number |
Part Description |
Qty |
| A |
138-7573 |
Link Bracket |
4 |
| ZZ |
6V-9507 |
Face Seal Plug (9/16 - 18 THD) |
1 |
| 6V-9828 |
Cap Assembly (9/16 - 18 THD) |
1 |
| 6V-9509 |
Face Seal Plug (13/16 - 16 THD) |
4 |
| 6V-9830 |
Cap Assembly (13/16 - 16 THD) |
4 |
Start By:
- Remove the rollover protective structure (ROPS). Refer to Disassembly and Assembly, "Rollover Protective Structure (ROPS) - Remove and Install".
Note: SERVICE DATA: TOOLING (ZZ) WILL NOT BE IDENTIFIED IN PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
Show/hide table
 |
Hot oil and components can cause personal injury. Do not allow hot oil or components to contact the skin. Be sure that the engine and components are cool enough to touch with your bare hand prior to performing any service work. |
 |
Show/hide table
|
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
|
Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.
Show/hide table
|
 |
|
| Illustration 1 | g01091236 |
- Remove bolts (3) and cover (4) .
- Remove bolts (2) and plate (1) .
Show/hide table
|
 |
|
| Illustration 2 | g01091258 |
- Disconnect harness assembly (5) .
Show/hide table
|
 |
|
| Illustration 3 | g01091262 |
- Remove bolts (7) and move harness assembly (6) out of the way.
Show/hide table
|
 |
|
| Illustration 4 | g01091268 |
- Disconnect cable assembly (8) .
Show/hide table
|
 |
|
| Illustration 5 | g01091277 |
- Disconnect harness assembly (9) and hose assemblies (10) .
Show/hide table
|
 |
|
| Illustration 6 | g01091282 |
- Attach Tooling (A) and a suitable lifting device to platform (11).
Show/hide table
|
 |
|
| Illustration 7 | g01091311 |
- Remove mounting bolts (12) from platform (11) .
Show/hide table
|
 |
|
| Illustration 8 | g01091313 |
- Raise platform (11) and install suitable wood blocks (13) .
Show/hide table
|
 |
|
| Illustration 9 | g01091355 |
- Remove nut (15) and cable assemblies (14) .
- Remove the platform from the machine. The weight of the platform is approximately 576 kg (1270 lb).
Installation Procedure
- Install the platform on the machine. The weight of the platform is approximately 576 kg (1270 lb).
Show/hide table
|
| |
|
| Illustration 10 | g01091355 |
- Install cable assemblies (14) and nut (15) .
Show/hide table
|
| |
|
| Illustration 11 | g01091313 |
- Raise the platform (11) and remove wood blocks (13) .
Show/hide table
|
| |
|
| Illustration 12 | g01091311 |
- Lower platform (11) and install mounting bolts (12) .
Show/hide table
|
| |
|
| Illustration 13 | g01091282 |
- Remove the suitable lifting device and Tooling (A) from the machine.
Show/hide table
|
| |
|
| Illustration 14 | g01091277 |
- Connect harness assembly (9) .
- Connect hose assemblies (10) .
Show/hide table
|
| |
|
| Illustration 15 | g01091268 |
- Connect cable assembly (8) .
Show/hide table
|
| |
|
| Illustration 16 | g01091262 |
- Reposition harness assembly (6) and install bolts (7) .
Show/hide table
|
| |
|
| Illustration 17 | g01091258 |
- Connect harness assembly (5) .
Show/hide table
|
| |
|
| Illustration 18 | g01091236 |
- Install plate (1) and bolts (2) .
- Install cover (4) and bolts (3) .
End By:
Install the rollover protective structure (ROPS). Refer to Disassembly and Assembly, "Rollover Protective Structure (ROPS) - Remove and Install".
