Gear Pump (Torque Converter Scavenge) - Disassemble
Start By:
- Remove the torque converter scavenge pump. Refer to Disassembly and Assembly, "Gear Pump (Torque Converter Scavenge) - Remove".
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly procedures on a clean work surface. Keep components covered and protected at all times.
Show/hide table
NOTICE |
---|
Failure to properly assemble parts or failure to follow established procedures can lead to damage of the parts and assembly. To avoid damage to parts, always identify and mark the parts so that they can be installed in the same location. Ensure that gear surfaces align. Never force parts during assembly. |
- For assembly purposes put an alignment mark across the cover and the body of the torque converter scavenge pump prior to disassembly.
Show/hide table
Illustration 1 g01067393 - Remove O-ring seals (2) and (3).
- Remove six bolts (1).
Show/hide table
Illustration 2 g01067394 - Remove cover (4).
Show/hide table
Illustration 3 g01067395 - Remove bearings (5).
Show/hide table
Illustration 4 g01067396 - Remove gears (6) and (7).
Show/hide table
Illustration 5 g01067398 - Remove body (8).
Show/hide table
Illustration 6 g01067399 - Remove four dowels (9).
Show/hide table
Illustration 7 g01067400 - Remove bearings (10).
Caterpillar Information System:
2004/06/14 New Cast Wheels Replace The Existing Cast Wheels {4201, 4209}
770 and 772 Off-Highway Truck Engine Oil and Filter - Change
120M and 12M Motor Graders Access Doors and Covers
C27 and C32 Engines for Caterpillar Built Machines Cylinder Head
8-16B and 10-20B Extend-A-Mat Screed Extender Carriage - Remove
120M and 12M Motor Graders Equipment Lowering with Engine Stopped
793C, 793C XQ and 793D Off-Highway Truck Fast Fill Fluid Center Fluids Service System Troubleshooting
248B and 268B Skid Steer Loaders Machine Systems Control Valve (Work Tool)
2004/05/03 New Transmission Solenoid Valve Groups Are Now Being Used {3174}
10-20B and 8-16B EXTEND A MAT SCREEDS Deflector Plate Adjustment (Strike-Off)
12M Motor Grader Seat
267B, 277B and 287B Multi Terrain Loaders Machine Systems Fuel Tank - Remove and Install
R2900G Load Haul Dump 3406E Engine Supplement Exhaust Purifier - Remove
R2900G Load Haul Dump Power Train Gear Pump (Torque Converter Scavenge) - Assemble
R1600G Load Haul Dump Remote Control System Relays
R2900G Load Haul Dump 3406E Engine Supplement Exhaust Purifier - Install
R1600G Load Haul Dump Remote Control System Receiver - Replace
R1600G Load Haul Dump Remote Control System Interface Control Module - Replace
2004/05/03 New Hoses For the Steering Cylinders Are Available {4304}
2004/04/19 Special Instruction, REHS2213, "Checking for Variations of the Torsion Axles" Is Available {3282, 4150}
2004/06/14 A New Piston Pin Retainer is Used {1214}
2004/06/01 A New Piston Pin Retainer is Used {1214}
414E, 416E, 420E and 430E Backhoe Loaders MID 039 - CID 1958 - FMI 03
414E, 416E, 420E and 430E Backhoe Loaders MID 039 - CID 1958 - FMI 04