Blade Lift Arm - Install
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 1P-1837     | Bearing Puller Adapter     | 1     |
6V-3170 | Double Acting Cylinder     | 1     | |
4K-0684 | Hard Washer     | 1     | |
4C-9634 | Puller Stud     | 1     | |
9U-6832 | Nut     | 1     | |
3S-6224 | Electric Hydraulic Pump Gp     | 1     | |
B     | 1P-1837     | Bearing Puller Adapter     | 1     |
6V-3170 | Double Acting Cylinder     | 1     | |
4K-0684 | Hard Washer     | 1     | |
1P-1835 | Bearing Puller Adapter     | 1     | |
4C-9634 | Puller Stud     | 1     | |
9U-6832 | Nut     | 1     | |
3S-6224 | Electric Hydraulic Pump Gp     | 1     | |
C     | 1P-0510     | Driver Gp     | 1     |
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Install Tooling (A) and support Tooling (A) with a suitable lifting device. Install bearings (26) .
Show/hide table
Illustration 1 | g01013647 |
Show/hide table
Illustration 2 | g01013181 |
- Use Tooling (C) and install lip seals (25) .
Show/hide table
Illustration 3 | g01013179 |
- Use Tooling (B) and install bearing (24) .
Show/hide table
Illustration 4 | g01013640 |
Show/hide table
Illustration 5 | g01013211 |
- Install seals (22) and washers (23). Use two people to install yoke (21) on blade lift arm (10). The weight of yoke (21) is approximately 23 kg (50 lb).
- Install shims (20). Use shims (20) to obtain a maximum end play of 0.254 mm (0.0100 inch). Yoke (21) must rotate freely. Install seal (19) .
- Install retainer (18) and bolts (17). Tighten bolts (17) to a torque of 129 ± 7 N·m (95 ± 5 lb ft).
- Install blade lift arm (10). The weight of blade lift arm is approximately 113 kg (250 lb).
Show/hide table
Illustration 6 | g01013176 |
- Install pin (16) .
- Install lock (15) and bolts (14) .
- Install pin (13) .
Show/hide table
Illustration 7 | g01013175 |
- Install lock (12) and bolts (11). Use the washers in order to obtain a clearance of 3.7 mm (0.15 inch) between the centershift lock bar and the plate.
- Attach a suitable lifting device to centershift cylinder (6) .
Show/hide table
Illustration 8 | g01013174 |
- Use the machine to position centershift cylinder (6).
- Install cap (8) and bolts (7) .
- Attach a suitable lifting device to blade lift cylinder (2). The weight of blade lift cylinder (2) is approximately 91 kg (200 lb).
Show/hide table
Illustration 9 | g01013173 |
- Position blade lift cylinder (2) on front frame assembly (5) .
- Install caps (4) and bolts (3) .
- Install plate (1), if equipped.
End By: If equipped, install the blade accumulators. Refer to Disassembly and Assembly, "Accumulator (Blade Cushion) - Remove and Install".
Caterpillar Information System:
143H and 163H Motor Graders Machine Systems Blade Lift Arm - Remove
2003/07/28 A New Idler Pulley is Used {1234}
TH220B and TH330B Telehandlers Engine Supplement Engine - Install
416D, 420D and 430D Backhoe Loaders Axles, Differential and Brakes Axle (Front)
CP-533E and CS-533E Vibratory Soil Compactors Machine Systems Electrical System
CP-533E and CS-533E Vibratory Soil Compactors Vibratory System Vibratory Electrical System
3126B Machine Engines Throttle Switch Circuit - Test
CP-533E and CS-533E Vibratory Soil Compactors Vibratory System Location of Electrical Components
143H and 163H Motor Graders Machine Systems Centershift Lock Bar and Front Frame Bushings - Install
143H and 163H Motor Graders Machine Systems Centershift Lock Bar and Front Frame Bushings - Remove
Machine Security System (MSS) Integrated Glossary of Terms
2003/08/04 Correction to Systems Operation , "Speed Control System" {4000, 4350}
R1600G Load Haul Dump Safety Messages
R1600G Load Haul Dump Model Views and Specifications
R1700G Load Haul Dump Air Conditioning and Heating Control
R1600G Load Haul Dump Lubricant Viscosities
Load Haul Dump Power Train Torque Converter
R2900G Load Haul Dump Steering System Diverter Valve (Secondary Steering)
R1600G Load Haul Dump Service Inspection
2003/08/01 A Previous High Temperature Locknut is Used in Engine Exhaust System Groups {7553}
247B, 257B, 267B, 277B and 287B Multi Terrain Loaders Safety Messages
2003/07/21 A New Fuel Priming Pump Is Used on the Wheel Feller Bunchers and the Wheel Skidders {1258}
R1600G Load Haul Dump Rear Axle Trunnion Bearings - Lubricate
R1600G Load Haul Dump Steering Cylinder Bearings - Lubricate