Blade Lift Arm - Remove
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 1P-1837     | Bearing Puller Adapter     | 1     |
6V-3170 | Double Acting Cylinder     | 1     | |
4K-0684 | Hard Washer     | 1     | |
9S-8546 | Seal Installer     | 1     | |
4C-9634 | Puller Stud     | 1     | |
9U-6832 | Nut     | 1     | |
3S-6224 | Electric Hydraulic Pump Gp     | 1     |
Start By:
- If equipped, remove the blade accumulators. Refer to Disassembly and Assembly, "Accumulator (Blade Cushion) - Remove and Install".
- If equipped, remove plate (1) .
Show/hide table
Illustration 1 | g01013173 |
- Attach a suitable lifting device to blade lift cylinder (2). The weight of blade lift cylinder (2) is approximately 91 kg (200 lb).
- Remove bolts (3) and caps (4) .
- Position blade lift cylinder (2) on front frame assembly (5). Secure blade lift cylinder (2) to the front frame assembly (5) .
- Attach a suitable lifting device to centershift cylinder (6) .
Show/hide table
Illustration 2 | g01013174 |
- Remove bolts (7) and cap (8) .
- Use the machine to retract centershift cylinder (6). Lower centershift cylinder (6) to the drawbar (9) .
- Attach a suitable lifting device to blade lift arm (10). The weight of blade lift arm is approximately 113 kg (250 lb).
Show/hide table
Illustration 3 | g01013175 |
- Remove bolts (11) and lock (12) .
- Remove pin (13) .
- Remove bolts (14) and lock (15) .
Show/hide table
Illustration 4 | g01013176 |
- Remove pin (16) .
- Remove blade lift arm (10). The weight of blade lift arm is approximately 113 kg (250 lb).
- Remove bolts (17) and retainer (18) .
Show/hide table
Illustration 5 | g01013640 |
- Remove seal (19) and shims (20) .
- Partially remove yoke (21) from blade lift arm (10).
- Use two people to remove yoke (21) from arm assembly (10). The weight of yoke (21) is approximately 23 kg (50 lb).
- Remove washers (23) and seals (22) .
- Remove bearings (24) .
- Remove lip seals (25) .
Show/hide table
Illustration 6 | g01013179 |
- Install Tooling (A) and support Tooling (A) with a suitable lifting device. Remove bearings (26) .
Show/hide table
Illustration 7 | g01013180 |
Show/hide table
Illustration 8 | g01013181 |
Caterpillar Information System:
2003/07/28 A New Idler Pulley is Used {1234}
TH220B and TH330B Telehandlers Engine Supplement Engine - Install
416D, 420D and 430D Backhoe Loaders Axles, Differential and Brakes Axle (Front)
CP-533E and CS-533E Vibratory Soil Compactors Machine Systems Electrical System
CP-533E and CS-533E Vibratory Soil Compactors Vibratory System Vibratory Electrical System
3126B Machine Engines Throttle Switch Circuit - Test
CP-533E and CS-533E Vibratory Soil Compactors Vibratory System Location of Electrical Components
143H and 163H Motor Graders Machine Systems Centershift Lock Bar and Front Frame Bushings - Install
143H and 163H Motor Graders Machine Systems Centershift Lock Bar and Front Frame Bushings - Remove
Machine Security System (MSS) Integrated Glossary of Terms
2003/08/04 Correction to Systems Operation , "Speed Control System" {4000, 4350}
2003/08/04 Correction to Systems Operation , "Pendulum Hydraulic System" {5050}
143H and 163H Motor Graders Machine Systems Blade Lift Arm - Install
R1600G Load Haul Dump Safety Messages
R1600G Load Haul Dump Model Views and Specifications
R1700G Load Haul Dump Air Conditioning and Heating Control
R1600G Load Haul Dump Lubricant Viscosities
Load Haul Dump Power Train Torque Converter
R2900G Load Haul Dump Steering System Diverter Valve (Secondary Steering)
R1600G Load Haul Dump Service Inspection
2003/08/01 A Previous High Temperature Locknut is Used in Engine Exhaust System Groups {7553}
247B, 257B, 267B, 277B and 287B Multi Terrain Loaders Safety Messages
2003/07/21 A New Fuel Priming Pump Is Used on the Wheel Feller Bunchers and the Wheel Skidders {1258}
R1600G Load Haul Dump Rear Axle Trunnion Bearings - Lubricate