Fuel System Primary Filter (Water Separator) Element - Replace
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
注意 |
---|
安装燃油滤清器之前不要在其中注入燃油。 否则燃油不会被过滤并可能受污染。 污染的燃油会加速燃油系统部件的磨损。 起动发动机之前应向燃油系统充注油。 |
- 打开机器左侧的发动机检修门。
Show/hide table
图 1 | g00841382 |
- 油水分离器位于主燃油滤清器的底部。 打开油水分离器杯上的排放阀。 让水和燃油排放到适当的容器内。
Show/hide table
图 2 | g01002123 |
1 型 |
- 使用带式扳手从滤清器安装底座卸下滤清器。
- 从滤清器滤芯中拆下油水分离器杯。 清洁油水分离器杯和 O 形密封圈槽。
注: 油水分离器杯可重复使用。 不要扔弃油水分离器杯。
- 钢制燃油滤清器(2 型)不可重复使用。
Show/hide table图 3 g01482573
2 型
- 检查油水分离器杯上的 O 形密封圈有无损坏。 如有必要,更换 O 形密封圈。
- 用干净的柴油或发动机机油润滑 O 型密封圈。 将 O 形密封圈放置到油水分离器杯上。
- 用手将油水分离器杯安装到新滤清器上。 不要用工具来拧紧油水分离器杯。
- 在新滤清器上涂抹薄薄的一层机油。 安装新滤清器,用手拧紧,直到发动机机油滤清器的密封圈与底座接触为止。 记下滤清器上分度标记相对于滤清器底座上固定点的相对位置。
注: 在燃油滤清器上有相互间隔 90 度或 1/4 圈的旋转分度标记。 拧紧燃油滤清器时,使用旋转分度标记作为参照。
Show/hide table
图 4 | g00101318 |
- 根据滤清器上的说明拧紧滤清器。 用分度标记作为参照。 对于非卡特彼勒滤清器,遵照随滤清器一起提供的说明书。
- 拧紧油水分离器杯上的排放阀。
注: 发动机正常运转过程中,油水分离器处于吸入状态。 排放阀必须拧紧,以防空气漏进燃油系统。
- 向燃油系统充油,以便将燃油注入燃油滤清器。
参考请参阅 操作和保养手册, "燃油系统充油" 以了解正确的程序。
Caterpillar Information System:
3044C Industrial Engine and Engines for Caterpillar Built Machines Crankshaft - Install
C27 and C32 Generator Set Engines CID 0444 FMI 06 Start Relay short to ground
C27 and C32 Generator Set Engines CID 0444 FMI 05 Start Relay open circuit
C-9 Engine for the 973C Track-Type Loader CID 0444 FMI 03 Start Relay short to +batt
2004/04/26 New Pin for the Hinge on the Off-Highway Truck Body Improves Service Life {7258}
3044C Industrial Engine and Engines for Caterpillar Built Machines Crankshaft - Remove
988H Wheel Loader Fuel System - Prime
836G Landfill Compactor and 834G Wheel Dozer Power Guard Control
561N Pipelayer Capacities (Refill)
924G and 924GZ Wheel Loaders Machine Systems Secondary Steering Pump and Electric Motor - Remove and Install
C-9 Engine for the 973C Track-Type Loader Cat Data Link Circuit - Test
2003/06/09 Correction to Specifications , "Pump Mounting (Hydroststic)" {3203}
988H Wheel Loader Fuel System Secondary Filter - Replace
120H and 135H Motor Graders Power Train Transmission Oil Filter Base - Disassemble
120H and 135H Motor Graders Power Train Transmission Oil Filter Base - Assemble
3044C Industrial Engine and Engines for Caterpillar Built Machines Crankshaft Gear - Remove and Install
561N, 572R Series II and 572R Pipelayers and D10R, D11R, D5M, D5N, D6M, D6N, D6R, D6R Series II, D7R, D7R Series II and D8R Series II Track-Type Tractors Power Train Electronic Control System MID 113 - CID 1933 - FMI 03
561N, 572R Series II and 572R Pipelayers and D10R, D11R, D5M, D5N, D6M, D6N, D6R, D6R Series II, D7R, D7R Series II and D8R Series II Track-Type Tractors Power Train Electronic Control System MID 113 - CID 1933 - FMI 05
561N, 572R Series II and 572R Pipelayers and D10R, D11R, D5M, D5N, D6M, D6N, D6R, D6R Series II, D7R, D7R Series II and D8R Series II Track-Type Tractors Power Train Electronic Control System MID 113 - CID 1933 - FMI 06
561N, 572R Series II and 572R Pipelayers and D10R, D11R, D5M, D5N, D6M, D6N, D6R, D6R Series II, D7R, D7R Series II and D8R Series II Track-Type Tractors Power Train Electronic Control System MID 113 - CID 1934 - FMI 03
561N, 572R Series II and 572R Pipelayers and D10R, D11R, D5M, D5N, D6M, D6N, D6R, D6R Series II, D7R, D7R Series II and D8R Series II Track-Type Tractors Power Train Electronic Control System MID 113 - CID 1934 - FMI 05
561N, 572R Series II and 572R Pipelayers and D10R, D11R, D5M, D5N, D6M, D6N, D6R, D6R Series II, D7R, D7R Series II and D8R Series II Track-Type Tractors Power Train Electronic Control System MID 113 - CID 1934 - FMI 06
C-9 Engine for the 973C Track-Type Loader CID 1639 FMI 09 Machine Security System Module not communicating on link
CP-533E and CS-533E Vibratory Soil Compactors Machine Systems Hydraulic Tank