Daily Inspection
Show/hide table
热油和热的部件可能会导致人员受伤。 同时,请勿让热的机油或热的零部件与皮肤接触。 在工作温度下,发动机冷却液是热的并且处于压力之下。 蒸汽还会引起人身伤害。 只有在停止发动机后,冷却系统的压力盖冷却到可以徒手触摸时,才能检查冷却液液位。 慢慢拧开冷却系统压力盖,以释放压力。 冷却系统添加剂含碱。 应避免皮肤和眼睛与其接触,以防造成人身伤害。 |
Show/hide table
注意 |
---|
机器上淀积的润滑脂和润滑油有引发火灾的危险。 用蒸汽或高压水来清除这些污物,至少每 1000 小时一次,或每当有大量的油溢漏在机器上时就要进行一次。 |
注: 为了使机器有最长的使用寿命,每天在操作前对机器做一次彻底的检查。 检查机器是否有泄漏之处。。 清除掉发动机舱中和行走装置上的所有残渣碎片。 确证所有的防护物、外罩和盖子都已安装牢固。 检查所有软管和皮带是否有损坏。 检查所有灯和后视镜有无损坏。 在操作机器前,先进行必要的修理。
每天完成以下事项:
- 操作和保养手册, "倒车警报器 - 测试"
- 操作和保养手册, "铲刀刃和端刀头 - 检查/更换"
- 操作和保养手册, "冷却系统冷却液液位 - 检查"
- 操作和保养手册, "发动机机油油位 - 检查"
- 参阅操作和保养手册, "发动机空气滤清器保养指示器-检查"
- 操作和保养手册, "液压系统油位 - 检查"
- 操作和保养手册, "座椅安全带 - 检查"
- 操作和保养手册, "变速器油位 - 检查"
- 操作和保养手册, "车窗 - 清洁"
欲知详细程序,请查阅保养部分。 查阅保养周期计划表,其中有全部计划保养的列表。
Caterpillar Information System:
3044C Industrial Engine and Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
CP-563C and CS-563C Vibratory Compactors Maintenance Interval Schedule
3044C Industrial Engine and Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
554, 564 and 574B Forwarders Window Washer Reservoir - Fill
3044C Industrial Engine and Engines for Caterpillar Built Machines Inlet Manifold - Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Inlet Manifold - Remove
2003/06/23 Special Instruction, REHS1638, "Rework Procedure for the Tube Assembly of the yoke" is Available {7050, 7051}
793C Off-Highway Truck Machine Systems Control Valve (Hoist) - Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Engine Oil Pan - Remove and Install
3044C Engine for Caterpillar Built Machines Camshaft Bearings - Remove and Install
725 and 730 Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Metering Pump (Steering)
980G Wheel Loader Bucket Lower Pivot Bearings - Lubricate
2003/07/14 A New Crankshaft Pulley is Available {1205}
3044C Industrial Engine and Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
834H Wheel Dozer and 836H Landfill Compactor Monitoring System
3044C Industrial Engine and Engines for Caterpillar Built Machines Pistons and Connecting Rods - Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove
3044C Industrial Engine and Engines for Caterpillar Built Machines Connecting Rod Bearings - Install
143H and 163H Motor Graders Power Train Control Valve (All Wheel Drive) - Remove
R1600G Load Haul Dump Power Train Electronic Control System Backup Alarm Always On
143H and 163H Motor Graders Power Train Control Valve (All Wheel Drive) - Install
R1600G Load Haul Dump Power Train Electronic Control System Backup Alarm Always Off
R2900G Load Haul Dump Power Train Electronic Control System MID 081 - CID 0627 - FMI 03
2003/06/09 A Duct to Demist the Rear Window is now Available {7320}