Housing (Front) - Install
Installation Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Clean all mating surfaces thoroughly.
- Install a new gasket (3) on the front plate. Be sure that gasket (3) properly fits on the dowel pins.
Note: Do not use sealant on the gasket.
Show/hide table
Illustration 1 | g01000873 |
- Apply clean engine oil to the lip of the crankshaft front seal.
Note: If a new crankshaft front seal needs to be installed, refer to Disassembly and Assembly, "Crankshaft Front Seal - Install".
- Position front housing (2) on the front of the cylinder block.
- Install bolts (1) and tighten to a torque of 10 to 13 N·m (7 to 10 lb ft).
End By:
- Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and Install".
- Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley - Remove and Install".
- Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Caterpillar Information System:
3044C Industrial Engine and Engines for Caterpillar Built Machines Housing (Front) - Remove
2003/07/14 Correction to Specifications , "Control Valve" {5051}
CP-533E and CS-533E Vibratory Soil Compactors Vibratory System Eccentric Weight Housing Group
CP-533E and CS-533E Vibratory Soil Compactors Vibratory System Vibratory Lines Group
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Machine Systems Cab - Install
988G Wheel Loader Crankshaft Vibration Damper - Inspect
M325D MH Material Handler Swing Gear - Lubricate
12H, 140H and 160H Motor Graders Power Train Differential and Bevel Gear - Assemble
12H, 140H and 160H Motor Graders Power Train Differential and Bevel Gear - Disassemble
3044C Industrial Engine and Engines for Caterpillar Built Machines Front Cover - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Idler Gear - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Crankshaft Front Seal - Install
CP-533E and CS-533E Vibratory Soil Compactors Vibratory System Vibratory Gauge Group
2003/06/02 Correction to Systems Operation, Testing and Adjusting , "Piston Pump (Steering and Pilot) Margin Pressure - Test and Adjust" {4306, 5070, 5085}
3044C Industrial Engine and Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install
988H Wheel Loader Engine Mounts - Inspect
2003/07/14 A New Rear View Mirror Improves Operator Visibility {7319}
CP-533E and CS-533E Vibratory Soil Compactors Vibratory System Eccentric Weight Shaft Group
988H Wheel Loader Engine Oil (High Speed) and Oil Filter - Change - If Equipped
2003/06/09 Charts for the Altitude Deration of Caterpillar Built Machines that are Powered By 3500 EUI and 3500B Engines {1902, 1923}
CP-533E and CS-533E Vibratory Soil Compactors Vibratory System Support and Vibratory Drive
3044C Industrial Engine and Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
3054E Engine for Caterpillar Built Machines Cylinder Head - Install
3054E Engine for Caterpillar Built Machines Cylinder Head - Remove