Eccentric Weight Housing Group
左侧偏心配重壳体总成
Show/hide table
图 1 | g01000841 |
(1) 为加注储油罐,加注口塞必须的位置位于旋转的顶部。
(2) 将 9S-3263 螺纹锁固胶 涂抹在六颗螺栓的螺纹上。
(3) 将 9S-3263 螺纹锁固胶 涂抹在八颗螺栓的螺纹上。
(4) 确保花键轴上的 "T" 朝上。总的轴向间隙应为 0.50 至 1.35 mm (0.012 至 0.053 in)。
(5) 两颗螺塞的扭矩 ... 90 ± 15 N·m (65 ± 10 lb ft)
(6) 这是检查油位用的螺塞。
注: 组装后的壳体应能承受 70 kPa (10 psi) 静态空气压力和 35 kPa (5 psi) 静态真空度。
注: 组装后,冲洗偏心配重壳体。要求的清洁度等级为 ISO 18/15 或以下。
右侧偏心配重壳体总成
Show/hide table
图 2 | g01000842 |
(7) 为加注储油罐,加注口塞必须的位置位于旋转的顶部。
(8) 将 9S-3263 螺纹锁固胶 涂抹在六颗螺栓的螺纹上。
(9) 将 9S-3263 螺纹锁固胶 涂抹在八颗螺栓的螺纹上。
(10) 确保花键轴上的 "T" 朝上。 总的轴向间隙应为 0.50 至 1.35 mm (0.012 至 0.053 in)。
(11) 两颗螺塞的扭矩 ... 90 ± 15 N·m (65 ± 10 lb ft)
(12) 这是检查油位用的螺塞。
注: 组装后的壳体应能承受 70 kPa (10 psi) 静态空气压力和 35 kPa (5 psi) 静态真空度。
Caterpillar Information System:
CP-533E and CS-533E Vibratory Soil Compactors Vibratory System Vibratory Lines Group
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Machine Systems Cab - Install
988G Wheel Loader Crankshaft Vibration Damper - Inspect
M325D MH Material Handler Swing Gear - Lubricate
12H, 140H and 160H Motor Graders Power Train Differential and Bevel Gear - Assemble
12H, 140H and 160H Motor Graders Power Train Differential and Bevel Gear - Disassemble
3044C Industrial Engine and Engines for Caterpillar Built Machines Front Cover - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Idler Gear - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Crankshaft Front Seal - Install
2003/06/16 High Temperature Hoses for the Brakes Improve Service Life {1374, 1380, 5057}
3044C Industrial Engine and Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove
2003/07/21 A New Procedure to Secure Wiring Harness in Articulating Area {1408}
2003/07/14 Correction to Specifications , "Control Valve" {5051}
3044C Industrial Engine and Engines for Caterpillar Built Machines Housing (Front) - Remove
3044C Industrial Engine and Engines for Caterpillar Built Machines Housing (Front) - Install
CP-533E and CS-533E Vibratory Soil Compactors Vibratory System Vibratory Gauge Group
2003/06/02 Correction to Systems Operation, Testing and Adjusting , "Piston Pump (Steering and Pilot) Margin Pressure - Test and Adjust" {4306, 5070, 5085}
3044C Industrial Engine and Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install
988H Wheel Loader Engine Mounts - Inspect
2003/07/14 A New Rear View Mirror Improves Operator Visibility {7319}
CP-533E and CS-533E Vibratory Soil Compactors Vibratory System Eccentric Weight Shaft Group
988H Wheel Loader Engine Oil (High Speed) and Oil Filter - Change - If Equipped
2003/06/09 Charts for the Altitude Deration of Caterpillar Built Machines that are Powered By 3500 EUI and 3500B Engines {1902, 1923}
CP-533E and CS-533E Vibratory Soil Compactors Vibratory System Support and Vibratory Drive