Vibratory Lines Group
Show/hide table
图 1 | g01000914 |
(1) 连接振动泵端口 "A" 和振动马达端口 "A" 的软管组件
(2) 两套支承卡箍之间的软管组件 (2) 的长度。 ... 610 ± 10 mm (24 ± 0.4 in)
(3) 两套支承卡箍之间的软管组件 (1) 和 (2) 的长度。 ... 300 mm (12 in)
(4) 两套支承卡箍之间的软管组件 (1) 的长度。 ... 670 ± 10 mm (26.4 ± 0.4 in)
(5) 将 7k-1181 电缆带 固定在软管组件 (1) 和 (2) 上以防止移动。将 7k-1181 电缆带 固定在支承卡箍的两侧上。
(6) 连接振动泵端口 "B" 和振动马达端口 "B" 的软管组件
(7) 螺栓的扭矩 ... 30 ± 7 N·m (22 ± 5 lb ft)
(8) 两套支承卡箍之间的软管组件 (1) 和 (2) 的长度。 ... 300 mm (12 in)
(9) 两套支承卡箍之间的软管组件 (1) 和 (2) 的长度。 ... 325 mm (13 in)
(10) 螺栓的扭矩 ... 30 ± 7 N·m (22 ± 5 lb ft)
Caterpillar Information System:
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders Machine Systems Cab - Install
988G Wheel Loader Crankshaft Vibration Damper - Inspect
M325D MH Material Handler Swing Gear - Lubricate
12H, 140H and 160H Motor Graders Power Train Differential and Bevel Gear - Assemble
12H, 140H and 160H Motor Graders Power Train Differential and Bevel Gear - Disassemble
3044C Industrial Engine and Engines for Caterpillar Built Machines Front Cover - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Idler Gear - Remove and Install
3044C Industrial Engine and Engines for Caterpillar Built Machines Crankshaft Front Seal - Install
2003/06/16 High Temperature Hoses for the Brakes Improve Service Life {1374, 1380, 5057}
3044C Industrial Engine and Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove
2003/07/21 A New Procedure to Secure Wiring Harness in Articulating Area {1408}
2003/06/23 A Modification to the Fuel Tank Group can Prevent Intermittent Interruptions. {1273, 1408}
CP-533E and CS-533E Vibratory Soil Compactors Vibratory System Eccentric Weight Housing Group
2003/07/14 Correction to Specifications , "Control Valve" {5051}
3044C Industrial Engine and Engines for Caterpillar Built Machines Housing (Front) - Remove
3044C Industrial Engine and Engines for Caterpillar Built Machines Housing (Front) - Install
CP-533E and CS-533E Vibratory Soil Compactors Vibratory System Vibratory Gauge Group
2003/06/02 Correction to Systems Operation, Testing and Adjusting , "Piston Pump (Steering and Pilot) Margin Pressure - Test and Adjust" {4306, 5070, 5085}
3044C Industrial Engine and Engines for Caterpillar Built Machines Crankcase Breather - Remove and Install
988H Wheel Loader Engine Mounts - Inspect
2003/07/14 A New Rear View Mirror Improves Operator Visibility {7319}
CP-533E and CS-533E Vibratory Soil Compactors Vibratory System Eccentric Weight Shaft Group
988H Wheel Loader Engine Oil (High Speed) and Oil Filter - Change - If Equipped
2003/06/09 Charts for the Altitude Deration of Caterpillar Built Machines that are Powered By 3500 EUI and 3500B Engines {1902, 1923}