A New Water Lines Clip Is Used on Certain G3516B and G3520B Petroleum Engines{1380, 7553}
- Engine:
- G3516 (S/N: 4EK1410-1410,1702-1702,1810-1810,3415-3415,3617-3617,3622-3622,3688-3688,3869-3869,3904-3904,3922-3922,3925-3925,4014-4014,4074-4074,4612-4612,4896-4896,5044-5044; WPW112-113,123-123,134-134,168-168,239-239,278-278,413-413,462-462,471-471,680-680,725-725,760-760,875-875,1010-1010,2454-2454,2640-2640,2837-2837)
- G3516B (S/N: JEF1-UP)
- G3520B (S/N: GLF1-UP)
- G3516B (S/N: JEF1-UP)
- Petroleum Engine:
- G3520B PETROLEUM (S/N: TPC1-UP)
Introduction
This Special Instruction provides the procedure in order to install the new water lines clip for the G3516B and G3520B Petroleum Engines. Refer to Table 1 for a list of new parts to install the water lines clip.
Required Parts
Show/hide table
Qty     | Part     |
---|---|
1     | 0S-1591 Bolt     |
2     | 2P-4437 Clip     |
1     | 4P-7233 Grommet     |
2     | 5M-2894 Hard Washer     |
1     | 6W-2928 Boss     |
1     | 9S-8752 Full Nut     |
1     | 353-7956 Grommet     |
Installing the New Water Lines Clip
- Locate the original water lines clip.
Show/hide table
Illustration 1 | g03422810 |
np (1) 6W-2928 Boss (2) 0S-1591 Bolt (3) 5M-2894 Hard Washer (4) 9S-8752 Full Nut (5) 353-7956 Grommet (6) 4P-7233 Grommet (7) 2P-4437 Clip |
- Remove the original water line clip and hardware.
- Install grommet (5) around the boost sensing line.
Note: Grommet (5) is install around the smaller line.
- Install grommet (6) around the water line.
- Install two clips (7) around grommets (5) and (6) use one boss (1), one bolt (2), two washers (3), and one nut (4) .
Caterpillar Information System:
C15 and C18 Engines for China On-Highway Phase IV Fuel Pressure Is Low
C15 and C18 Engines for China On-Highway Phase IV Fuel Pressure Is High
C15 and C18 Engines for China On-Highway Phase IV Diesel Particulate Filter Has Low Inlet Pressure
C15 and C18 Engines for China On-Highway Phase IV Diesel Particulate Filter Has High Inlet Pressure
C15 and C18 Engines for China On-Highway Phase IV ARD Temperature Is Low
C15 and C18 Engines for China On-Highway Phase IV ARD Loss of Combustion
3600 and C280 Diesel Engine Fluids Recommendations General Coolant Information
C15 and C18 Engines for China On-Highway Phase IV ARD Fuel Pressure Is Low
C15 and C18 Engines for China On-Highway Phase IV ARD Fuel Pressure Is High
2013/11/13 Special Instructions Are Available for Installing a New Water Lines Clip on G3516B and G3520B Petroleum Engines {1380, 7553}
3600 and C280 Diesel Engine Fluids Recommendations Coolant Recommendations - General Maintenance
C15 and C18 Engines for China On-Highway Phase IV ARD Failed to Ignite
C15 and C18 Engines for China On-Highway Phase IV Sensor Signal (Analog, Active) - Test
C15 and C18 Engines for China On-Highway Phase IV Sensor Calibration Required - Test
C15 and C18 Engines for China On-Highway Phase IV NRS Exhaust Gas Temperature Is High
C15 and C18 Engines for China On-Highway Phase IV NOx Reduction System (NRS) - Test
C15 and C18 Engines for China On-Highway Phase IV Intake Manifold Air Pressure Is Low
C15 and C18 Engines for China On-Highway Phase IV Injector Solenoid - Test
C15 and C18 Engines for China On-Highway Phase IV Fuel Temperature Is High
C15 and C18 Engines for China On-Highway Phase IV Exhaust Balance Valve - Test
C15 and C18 Engines for China On-Highway Phase IV Ether Starting Aid - Test
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies DC Bus Capacitor - Remove and Install
C15 and C18 Engines for China On-Highway Phase IV Electrical Power Supply - Test
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Front Screen and Air Filter