Cylinder Block
Show/hide table
Illustration 1 | g03043396 |
Front view |
Show/hide table
Specification for 219-4711 Cylinder Block Gp | |||
Item | Qty | Part | Specification Description |
The top face of the cylinder block, bottom surface of spacer plate (2) and both sides of plate gasket (4) must be free of fuel, oil, water, gasket adhesives, assembly compounds and any other contaminants during assembly. | |||
1 | 2 | 4W-4813 Plug | Torque to |
2 | 16 | 110-6994 Spacer Plate | Thickness is |
3 | 32 | 8T-0099 Dowel | Extension of the dowel is |
4 | 16 | 144-5692 Plate Gasket | Thickness of plate gasket that is between cylinder block and spacer plate is |
5 | 16 | 197-7008 Dowel | Extension of the dowel is |
A | 18 | 116-1359 Camshaft Bearing | Bore in the block for the camshaft bearing is |
B | - | - | All centerlines through oil holes in the camshaft bearings and the camshaft bearing junctions (6) are shown for each side of the cylinder block. |
Oil holes must be positioned from horizontal at an angle of 20.0 ± 0.5 degrees. | |||
C | - | - | New dimension from centerline of crankshaft bearing bore to the top of the block is |
7 | 8 | 6V-3348 O-Ring Seal | Lubricate the bore lightly with sealant that is being sealed. |
8 | 9 | 223-1696 Crankshaft Bearing Cap | Install crankshaft bearing caps with the part number and FRONT toward the front of the block. Each cap has a number. Each cap must be installed in the same position as the correct number on the side of the cylinder block pan rail.
Width of crankshaft bearing cap (D) is Width of cylinder block for crankshaft bearing cap is |
- | - | - | Bore (E) in the block for the crankshaft bearings is |
- | - | - | New dimension (F) from centerline of crankshaft bearing bore to bottom of block (pan rails) is |
9 | 36 | 7X-7925 Bolt | Use the following procedure to in order to tighten the bolts of crankshaft bearing cap:
1. Lubricate the threads with clean engine oil before assembly. 2. Tighten the bolts by hand. 2. Tighten the bolts in the numerical sequence as shown in Illustration 1 to 3. Again tighten the bolts in the numerical sequence as shown in Illustration 1 to an angle of 180 ± 5 degrees. |
Show/hide table
Illustration 2 | g03043397 |
Right side view |
Show/hide table
Item | Qty | Part | Specification Description |
G | 1 | 7N-2047 Dowel | Extension of the dowel is |
H | 2 | 7N-2047 Dowel | Extension of the dowel is |
J | 2 | 4N-0683 Dowel | Extension of the dowel is |
K | 2 | 7N-2044 Dowel | Extension of the dowel is |
10 | 4 | 5F-9657 O-Ring Seal | Lubricate the bore lightly with sealant that is being sealed. |
11 | 2 | 5P-8210 O-Ring Seal | Lubricate the bore lightly with sealant that is being sealed. |
12 | 3 | 7X-4805 O-Ring Seal | Lubricate the bore lightly with sealant that is being sealed. |
13 | 5 | 214-7568 O-Ring Seal | Lubricate the bore lightly with sealant that is being sealed. |
Caterpillar Information System:
G3500B Engines Crankshaft
3516B Engine for the MT4400D Off-Highway Truck Turbocharger
2013/08/21 A New High-Temperature Tee Hose Is Available for Crankcase Breathers on 3500, G3500, 3600, G3600, and C280 Engines {1317}
2012/09/27 A New High-Temperature Tee Hose Is Available for Crankcase Breathers on 3500 Machine Engines {1317}
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Lubricant Viscosities
UPS 1000Z, UPS 1200Z, UPS500G and UPS600G Uninterruptible Power Supplys Bearing (Earlier) - Replace
UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Bearing (3.5 EVD or Greater) - Replace
UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Bearing (Earlier) - Replace
3512C and 3516C Marine Engines Fumes Disposal System
C7.1 Industrial Engine Cooling System
3512B, 3512C, and 3516B Generator Set Engines with Dynamic Gas Blending Restriction of Air Inlet and Exhaust
3512C and 3516C Marine Engines Turbocharger
G3516C and G3516E Gas Engines Cylinder Block
C18 Marine Engines Electronic Unit Injector - Remove and Install
3516B Engine for the MT4400D Off-Highway Truck Fuel Injector
C18 Marine Engines Electronic Unit Injector Sleeve - Remove and Install
C18 Marine Engines Turbocharger - Remove and Install
G3516C and G3516E Gas Engines Camshaft Bearing Position
C18 Marine Engines Inlet and Exhaust Valve Springs - Remove and Install
C18 Marine Engines Inlet and Exhaust Valves - Remove and Install
2012/05/21 Viewing the Electronic Thermostat Position via ET on C175 Engines {135V, 7610}
C18 Marine Engines Inlet and Exhaust Valve Guides - Remove and Install
C18 Marine Engines Inlet and Exhaust Valve Seat Inserts - Remove and Install
2012/05/21 New Clamping for the Jacket Water Bypass Tube on Certain 3500 Engines {1380, 7553}