3512C and 3516C Marine Auxiliary and Generator Set Engines Caterpillar


Fumes Disposal Filter Element - Replace

Usage:

3512C 2A2
烟雾处理过滤器的维修间隔受下列条件影响:

  • 发动机的负载

  • 烟尘浓度

  • 发动机状况


图 1g02728287
发动机左侧
(1) 烟雾处理组件
(2) 发动机曲轴箱通气孔

------ WARNING! ------

热油和热的部件可能会导致人员受伤。 不要让热的油和部件接触皮肤。




    图 2g02728732
    (3) 烟雾处理过滤器盖
    (4) 烟雾处理过滤器碳罐
    (5) 将碳罐与盖相连的锁耳


    注意

    在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。

    有关适于收集和盛放 Cat 产品油液的工具和用品,请参阅专门出版物, NENG2500, "Cat 代理商维修工具目录"或专门出版物, PECJ0003, "Cat 车间用品和工具目录"。

    按照本地法规和要求处置所有油液。


  1. 松开锁耳并压在碳罐上以拆除碳罐。

    注: 发动机运转过程中可能很难拆卸碳罐。 发动机运行时,碳罐产生负气压,形成真空。

  2. 拆除旧滤清器。 滤清器和碳罐中有可能含有发动机油。 可能包含所有油液。

  3. 卸下旧滤芯顶端盖上的 O 形密封圈。 将新 O 形密封圈安装到新滤清器顶部。

  4. 卸下滤清器底部的 O 形密封圈。 检查用过的密封件有无磨损或损坏。 将未损坏的 O 形密封圈安装到新滤清器底部。

  5. 弃置旧滤清器。

  6. 安装一个新的滤清器。 将碳罐与盖正确对中并夹紧锁耳。

注: Caterpillar 对因改装滤清器或使用 Caterpillar 未批准的滤清器而不符合排放标准的发动机不予负责。

Caterpillar Information System:

CT660 CX31 and CX31 HT On Highway Truck Power Train Electronic Control System Transmission - Calibrate
3512C Petroleum Engines Data Link Configuration Status - Test
2011/10/10 A New Charging Alternator Group Is Used on C18 Engines In Certain Products {1405}
319-2187 Diesel Particulate Filter (DPF) Cleaner {0374, 0599, 0680, 0701, 0702, 108D} 319-2187 Diesel Particulate Filter (DPF) Cleaner {0374, 0599, 0680, 0701, 0702, 108D}
2011/12/15 A New Service Tool for Installing the Service Sleeve Bearings in Hydraulic Gear Pumps Is Now Available for Certain CAT Machines {0738, 5073, 5073, 7551}
Installation of the 324-7875 Control Box Gp for G3600 Engines {1917, 1924, 4460, 7426} Installation of the 324-7875 Control Box Gp for G3600 Engines {1917, 1924, 4460, 7426}
320E and 323E Excavators Machine System Specifications Boom Lines
320E and 323E Excavators Machine System Specifications Boom Cylinder Lines
312F and 313F Excavators Plate Locations and Film Locations
3512C and 3516C Marine Auxiliary and Generator Set Engines Gauges and Indicators
3512C HD and 3516C HD Class I Division 2 Hazardous Location Generator Sets Engine Electronics
PM3516 Power Modules Generator Bearing Temperature - Test/Record
320 GC, 320 and 323 Excavator Machine Systems Specifications Refrigerant Compressor
C13, C15, and C18 Tier 4 Final Engines Cylinder Head
CT660 CX31 and CX31 HT On Highway Truck Power Train Electronic Control System Electronic Control Unit - Flash Program
Model HCS-40 Hydraulic Cylinder Servicer{0374, 0599, 0700, 0738, 7562} Model HCS-40 Hydraulic Cylinder Servicer{0374, 0599, 0700, 0738, 7562}
C3.4B Engines Diesel Particulate Filter Active Regeneration Was Interrupted
2011/10/28 Correct Orientation of the V-Band Clamp on the Center Housing/Turbine Housing Joint Is Needed on Certain C15 Truck Engines {1052, 1053}
3500 Generator Sets Engine Air Cleaner Element (Dual Element) - Inspect/Clean/Replace
3500 Generator Sets Engine Air Cleaner Element (Single Element) - Inspect/Clean/Replace
3500 Generator Sets Engine Air Precleaner - Check/Clean
3516C Industrial Engine Product Lifting
2011/11/16 A New Turbocharger Water Line Is Used for Certain 3516B and 3516C Engines {1380}
2011/12/23 Special Instruction, REHS7409, "Initial Start-Up of CG137 and G3300B Engines" Is Available {1000}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.