Backlight Does Not Illuminate
系统运作描述:
Show/hide table
图 1 | g02237982 |
"背光调节"开关是众多带背光的开关之一,位于卡车驾驶室内。 |
注: 该文档中的故障诊断与排除信息也适用于以下开关的背光:"辅助转向测试开关", "经济模式测试开关" 和 "加热式视镜开关"。
ECM 不出于诊断目的监控此回路。
通过此步骤,可检查所有类似的摇臂开关 LED 背光回路。 所有背光 LED 指示灯均是摇臂开关的组成部分。 指示灯不可更换。
如果摇臂开关接通时背光不点亮,执行以下步骤:
测试步骤 1. 核实背光不能点亮
- 把钥匙开关转到接通位置。
- 观察背光。
注: 核实背光没有变暗。 使用"背光调节"开关增加背光强度。 如果背光处于明亮的日光中,遮住背光并确认背光没有点亮。
预期结果:
背光点亮。
结果:
- 确定 - 背光点亮。 此时不存在该故障。 允许机器恢复使用。停止
- 异常 - 背光熄灭。 转至测试步骤 2。
测试步骤 2. 检查断开的电源电路或接地电路的线束
- 将钥匙开关转到断开位置。
- 从线束上断开所有相关的 ECM 模块。
- 从摇臂开关上断开线束。
- 获得背光回路的触针和导线编号。 确认所执行工作机器的电气示意图中的触针和导线编号。
- 测量线束中背光触点与相应的 ECM 触点之间的电阻。
预期结果:
各电阻均小于 5 欧姆。
结果:
- 确定 - 各电阻均小于 5 欧姆。 线束中的电路正常。 背光 LED 指示灯可能出现故障。
修复: 更换含有 LED 指示灯的摇臂开关。
转至测试步骤 3。
- 异常 - 电阻大于 5 欧姆。
修复: 修理或更换线束。
转至测试步骤 3。
测试步骤 3. 执行所有工作检查
- 重新连接已拆卸的所有接头。
- 将钥匙开关转到接通位置。
- 确认背光点亮。
预期结果:
钥匙开关接通时背光点亮,钥匙开关断开时背光熄灭。
结果:
- 确定 - 背光工作正常。 允许机器恢复使用。停止
- 异常 - 背光工作不正常。 底盘 ECM 可能有故障,但 ECM 出现故障的可能性不大。
修复: 请联系您代理商的技术通讯员,咨询 Caterpillar 的建议。 如果必须更换 ECM,请参阅本手册中的测试和调整, "电子控制模块(ECM)- 更换"章节。
停止
Caterpillar Information System:
C3.4B Engines Diesel Particulate Filter Collects Excessive Soot
C3.4B Engines Coolant Level Is Low
Final Drive Steering System, Wheel Braking System, and Wheels & Tires Salvage and Reuse Manual Contents {4000, 4050, 4100, 4250, 4300} Final Drive Steering System, Wheel Braking System, and Wheels & Tires Salvage and Reuse Manual Contents {4000, 4050, 4100, 4250, 4300}
C15 and C18 Engines Product Lifting
2011/03/16 A New Cylinder Head Gasket and Spacer Plate Are Used for 3500 Machine Engines {1100, 1201, 7555}
C9.3 Industrial Engine and CX31-P600-C9I Petroleum Power Train Package Fuel System - Prime
C15 and C18 Engines Overhaul Considerations
2010/08/26 Service Tips for the Hydraulic Electronic Unit Injector HEUI Pump {1714}
C27 and C32 Engines for Caterpillar Built Machines Exhaust Cooler (NRS) - Remove and Install
3500B and 3500C Marine Propulsion Engines E048 Backup ECM Took Control
2010/09/01 Changes to the Usage and Cleaning of the Contamination Monitor Group {0645, 0680, 1280, 1348, 3080, 429F, 5095}
C7.1 Industrial Engine Diagnostic Flash Code Retrieval
3306B Generator Set Refill Capacities and Recommendations
3306B Generator Set Generator Bearing - Inspect
3306B Generator Set Alternator and Fan Belts - Inspect/Adjust/Replace
3500B Generator Sets Generator Bearing - Lubricate
3306B Generator Set Generator Bearing Temperature - Measure/Record
3306B Generator Set Safety Messages
312F and 313F Excavators Belt - Inspect/Adjust/Replace
C27 and C32 Engines for Caterpillar Built Machines Exhaust Sensor Lines - Remove and Install
3512B Petroleum Engines with the ADEM 2 Electronic Control Module E012 High Crankcase Pressure Derate
UPSB125 Uninterruptible Power Supply UPS Battery - 50Hz Basic Preventive Maintenance
UPSB125 Uninterruptible Power Supply UPS Battery - 50Hz Advanced Preventive Maintenance
C3.4B Engines Diesel Particulate Filter Temperature Is Low