Drive Shaft (Main) - Remove and Install
拆卸步骤
开始:
- 安装车斗固定电缆。 请参阅拆解和组装, "车斗固定电缆 - 拆卸和安装"。
- 拆下前驱动轴护罩。 请参阅拆解和组装, "驱动轴护罩(前)- 拆卸和安装"。
- 拆下后驱动轴护罩。 请参阅拆解和组装, "驱动轴护罩(后)- 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
车斗降下后,车斗与机架之间没有空隙。 如果不安装固定缆线,可能会导致在此区域作业的人员受伤或死亡。 |
- 将垫块安装在中心管中以支撑驱动轴。
- 使用适当的起吊设备支撑驱动轴 (1) 。 驱动轴 (1) 的重量约为 172 kg (380 lb)。
Show/hide table
图 1 | g01276414 |
- 卸下螺栓 (2) 。
- 弃置螺栓 (2) 。
- 缩回驱动轴 (1) 。
Show/hide table
图 2 | g01276425 |
- 拆卸螺栓 (3) 和 十字轴 (4) 。 十字轴 (4) 的重量大约为 20 kg (44 lb)。
- 弃置螺栓 (3) 。
- 使用适当的起吊设备支撑驱动轴 (1) 。 驱动轴 (1) 的重量约为 172 kg (380 lb)。
Show/hide table
图 3 | g01276429 |
- 卸下螺栓 (5) 。
- 弃置螺栓 (5) 。
- 缩回驱动轴 (1) 。
Show/hide table
图 4 | g01276434 |
- 拆下螺栓 (6) 和 十字轴 (7) 。 十字轴 (7) 的重量大约为 20 kg (44 lb)。
- 弃置螺栓 (6) 。
- 从中心管上拆下垫块。
- 使用适当的起吊设备来拆下驱动轴 (1) 。 驱动轴 (1) 的重量约为 172 kg (380 lb)。
注: 拆下朝向机器后部的驱动轴。
Show/hide table
图 5 | g01276449 |
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
车斗降下后,车斗与机架之间没有空隙。 如果不安装固定缆线,可能会导致在此区域作业的人员受伤或死亡。 |
- 使用适当的起吊设备来安装驱动轴 (1) 。 驱动轴 (1) 的重量约为 172 kg (380 lb)。
注: 从机器后部安装驱动轴。
Show/hide table
图 6 | g01276449 |
- 将垫块安装在中心管中以支撑驱动轴。
- 安装十字轴 (7) 。 十字轴 (7) 的重量大约为 20 kg (44 lb)。 安装新螺栓 (6) 。 拧紧螺栓 (6) 至扭矩为 550 ± 20 N·m (406 ± 15 lb ft)。
Show/hide table
图 7 | g01276434 |
- 使用适当的起吊设备将驱动轴 (1) 连接到变速箱轭。 驱动轴 (1) 的重量约为 172 kg (380 lb)。
- 安装新螺栓 (5) 。 拧紧螺栓 (5) 至扭矩为 550 ± 20 N·m (406 ± 15 lb ft)。
Show/hide table
图 8 | g01276429 |
- 安装十字轴 (4) 。 十字轴 (4) 的重量大约为 20 kg (44 lb)。 安装新螺栓 (3) 。 拧紧螺栓 (3) 至扭矩为 550 ± 20 N·m (406 ± 15 lb ft)。
Show/hide table
图 9 | g01276425 |
- 使用适当的起吊设备将驱动轴 (1) 连接到变矩器轭。 驱动轴 (1) 的重量约为 172 kg (380 lb)。
- 安装新螺栓 (2) 。 拧紧螺栓 (2) 至扭矩为 550 ± 20 N·m (406 ± 15 lb ft)。
Show/hide table
图 10 | g01276414 |
- 取下止块。
End By:
- 安装前驱动轴护罩。 请参阅 拆解和组装, "驱动轴护罩(前)- 拆卸和安装"。
- 安装后驱动轴护罩。 请参阅 拆解和组装, "驱动轴护罩(后)- 拆卸和安装"。
- 拆下车斗固定电缆。 请参阅 拆解和组装, "车斗固定电缆 - 拆卸和安装"。
Caterpillar Information System:
AccuGrade® GPS Using The CD550A Display (GPS/ATS/Sonic/Cross Slope) Machine Type - Configure - Machine Settings
AccuGrade® GPS Using The CD550A Display (GPS/ATS/Sonic/Cross Slope) Machine Dimensions - Configure
AccuGrade® GPS Using The CD550A Display (GPS/ATS/Sonic/Cross Slope) Light Bar - Configure
R1700G Load Haul Dump Power Train NoSPIN Differential
773E, 773F, 775F, 777E, and 777F Off-Highway Truck Brake Electronic Control System MID 116 - CID 1326 - FMI 02
773E, 773F, 775F, 777E, and 777F Off-Highway Truck Brake Electronic Control System MID 116 - CID 2683 - FMI 08
773E, 773F, 775F, 777E, and 777F Off-Highway Truck Brake Electronic Control System MID 116 - CID 2683 - FMI 04
773E, 773F, 775F, 777E, and 777F Off-Highway Truck Brake Electronic Control System MID 116 - CID 2683 - FMI 03
R1700G Load Haul Dump Power Train Differential and Bevel Gear (NoSPIN)
773E, 773F, 775F, 777E, and 777F Off-Highway Truck Brake Electronic Control System MID 116 - CID 0713 - FMI 04
Procedure to Fill Gear Pump with Oil Before Start-Up{5073} Procedure to Fill Gear Pump with Oil Before Start-Up{5073}
572R Series II Pipelayer Fast Fill Fuel Adapter
583T Pipelayer Machine Systems Fast Fill Fuel Adapter
3176C Engines for Caterpillar Built Machines Engine Temperature Sensor Open or Short Circuit - Test
583T Pipelayer Machine Systems Fast Fill Fuel Adapter
2006/11/13 Troubleshooting the Injection Actuation Pressure on Unit Injector Hydraulic Pumps {1714}
572R Series 2, 583T, 587T, PL83 and PL87 Pipelayers Fast Fill Fuel System - 583T PL83 587T PL87 And 572R II
3176C Engines for Caterpillar Built Machines Decelerator Position Sensor Circuit - Test
587R Pipelayer Machine Systems Fast Fill Fuel Adapter
2006/08/14 Caterpillar Factory Commissioning Services {1000, 4450, 7000, 7002}
587R Pipelayer Machine Systems Fast Fill Fuel Adapter
Field Installation of 284-8542 Backhoe Lines Gp (Kit, Field Conversion){5057} Field Installation of 284-8542 Backhoe Lines Gp (Kit, Field Conversion){5057}
Some Backhoe Loaders with Front Windows May Crack the Front Window{7301, 7310} Some Backhoe Loaders with Front Windows May Crack the Front Window{7301, 7310}
Starting and Charging Systems Main Relay and/or Breaker Test Description