UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Caterpillar


Zig Zag Overload Relay (SMS Bypass Cabinet)

Usage:

UPS 250 APZ


Description



Illustration 1g01270179
(1) Zig Zag Overload Relay

The Zig Zag Overload Relay (ZZOL) (1) is mounted on the rear panel. The Zig Zag Overload Relay is also known as OLR1. The OLR1 (1) is required for maintaining the ground reference of the 3-phase output when the system is in discharge mode and the system is disconnected from the utility input.

The Overload Relay (1) is used with the internal resistor (R19) to provide a solid ground for the system.

Removal Procedure

Refer to Systems Operation, Testing and Adjusting, RENR9988, "Internal Component Preremoval Steps (SMS Bypass Cabinet)" in order to shut down the system and gain access to internal components.

  1. Disconnect the wires from the ZZOL Relay (1). Verify the labeling of the wires for subsequent installation.

  2. Remove the rail stop on the right side of the ZZOL Relay (1) by loosening the two screws. Slide the rail stop off the rail.

  3. Remove the ZZOL Relay (1) by sliding the relay off the rail.

Installation Procedure

  1. Attach the ZZOL Relay (1) onto the rail by placing the top of relay on the top edge of the rail. Snap the bottom of the relay into place. Refer to Illustration 1 for placement.

  2. Slide the rail stop over the rail and attach the rail stop. Fasten the rail stop in place with two screws.


    Illustration 2g01270235
    Zig Zag Overload Relay Wire Connections

  3. Attach the wires to the ZZOL Relay (1). Verify the labeling of the wires with the location of the wires. Refer to Illustration 2 for wire connections.

Caterpillar Information System:

UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Zig Zag Circuit Breaker (SMS Bypass Cabinet)
TA22 Transmission Temperature Sensor (Transmission Oil) - Remove and Install
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Zig Zag Contactor (SMS Bypass Cabinet)
TA22 Transmission Relief Valve (Transmission Main) - Install
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Vacuum Pump Oil - Change
TA22 Transmission Relief Valve (Transmission Main) - Remove
TA22 Transmission Speed Sensor (Transmission) - Install
G3406 and G3412 Generator Sets Starting the Engine
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Zig Zag Transformer (SMS Bypass Cabinet)
TA22 Transmission Speed Sensor (Transmission) - Remove
C9 Marine Engines and C9 Marine Generator Sets Unit Injector Hydraulic Pump
3500C Marine Engines Turbocharger
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines E360 Low Engine Oil Pressure
C4.4 Industrial Engine Fuel Injection Timing - Check
TA19-M2WD and TA19-M4WD Agricultural Transmissions Relief Valve (Transmission Main) - Assemble
TA19-M2WD and TA19-M4WD Agricultural Transmissions Relief Valve (Transmission Main) - Disassemble
TA22 Transmission Modulating Valve (Transmission Clutch) - Remove and Install
C175-16 and C175-20 Generator Set Engines Exhaust Fitting
TA22 Transmission Pressure Sensor (Charge Pump) - Remove and Install
UPS 120, UPS 150, UPS 250, UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Static Drain - Install
TA22 Transmission Transmission - Disassemble
TA22 Transmission Transmission - Assemble
TA22 Transmission Pump Drive - Remove
TA22 Transmission Pump Drive - Install
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.