Stick - Install
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 4C-6486     | Stand     | 1     |
8S-7641 | Tube     | 1     | |
8S-8048 | Saddle     | 1     | |
8S-7615 | Pin     | 1     | |
B     | 189-0863     | Shackle     | 1     |
140-7742 | Sleeve     | 1     | |
D     | 4C-9485     | Pin Driver Cap     | 1     |
Note: Make sure that the pin bores in the stick and in the boom are thoroughly clean and free of dirt and debris prior to the installation of the stick on the boom.
- Reinstall pin assembly (3) and bolt (2) onto stick (5) and attach a suitable lifting device, as shown. Attach Tooling (B) and a suitable lifting device to the opposite end of stick (5), as shown. The weight of stick (5) is approximately 1451 kg (3200 lb).
Show/hide table
Illustration 1 | g01176082 |
Show/hide table
Illustration 2 | g01176562 |
- Position stick (5) onto the boom.
- Attach a suitable lifting device to pin assembly (7). Use Tooling (D) (not shown) to position pin assembly (7). Install pin assembly (7) and bolt (6). The weight of pin assembly (7) is approximately 36 kg (80 lb). Remove Tooling (D) from pin assembly (7) .
Show/hide table
Illustration 3 | g01176084 |
- Remove bolt (2) and pin assembly (3). Refer to illustration 1.
- Connect hose assemblies (4). Repeat this step for the opposite side.
Show/hide table
Illustration 4 | g01176081 |
- Attach a suitable lifting device to stick cylinder (1). The weight of stick cylinder (1) is approximately 193 kg (425 lb). Position stick cylinder (1) and install pin assembly (3) and bolt (2). Remove the suitable block and the suitable lifting device.
Show/hide table
Illustration 5 | g01176079 |
- Start the machine and remove Tooling (A) .
Show/hide table
Illustration 6 | g01176078 |
End By: Install the bucket. Refer to Disassembly and Assembly, "Bucket - Install".
Caterpillar Information System:
325C LCR Excavator Machine Systems Stick - Remove
C15 and C18 Petroleum Generator Sets Engine Oil and Filter - Change
302.5C Mini Hydraulic Excavator Engine Supplement Fuel Filter and Water Separator Base - Remove and Install
2006/03/27 The Reliability and Durability of the Electric Starting Motor Is Increased {1408, 1417, 1453, 7499}
2005/06/27 Improved Engine Oil Coolers are Now Used {1378}
Pin Grabber Quick Coupler Spring (Blocking Bar) - Replace
M318C and M322C Wheeled Excavators Power Train Differential - Assemble - Rear
M318C and M322C Wheeled Excavators Power Train Differential - Disassemble - Rear
345B Series II Excavator Hydraulic System (Ecomate Attachment) Bucket Hydraulic System
302.5C Mini Hydraulic Excavator Engine Supplement Engine - Install
345C MHPU Mobile Hydraulic Power Unit Machine Systems Gear Pump (Pilot) - Install
345C MHPU Mobile Hydraulic Power Unit Machine Systems Gear Pump (Pilot) - Assemble
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Track - Remove and Install
302.5C Mini Hydraulic Excavator Engine Supplement Refrigerant Compressor - Remove and Install
302.5C Mini Hydraulic Excavator Engine Supplement Refrigerant Receiver-Dryer - Remove and Install
385C Excavator and 385C MHPU Mobile Hydraulic Power Unitwith UHD Attachment Demolition Boom Removal
302.5C Mini Hydraulic Excavator Engine Supplement Fuel Transfer Pump - Remove and Install
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Swivel - Remove
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Seat - Remove and Install
302.5C Mini Hydraulic Excavator Machine Systems Swivel - Disassemble
302.5C Mini Hydraulic Excavator Machine Systems Swivel - Assemble
302.5C Mini Hydraulic Excavator Engine Supplement Refrigerant Condenser - Remove and Install
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Selector Valve (Alternate Pattern Control) - Remove and Install
301.6C and 301.8C Mini Hydraulic Excavators Machine Systems Front Idler, Recoil Spring and Hydraulic Track Adjuster - Remove and Install