New Hose Improves the Drainage of Oil from the Turbocharger During a Continuous Prelube Cycle {1052}
- Engine:
- 3508 (S/N: 95Y1-UP)
- G3508 (S/N: 4WD1-UP; 9TG1-UP; CTN1-UP)
- G3512 (S/N: 4KC1-UP; 5JD1-UP; 7NJ1-UP; CTM1-UP)
- G3516 (S/N: 3RC1-UP; 8LD1-UP; 4EK1-UP; CTL1-UP)
- G3516B (S/N: CEY1-UP; CTW1-UP)
- G3520B (S/N: GET1-UP; BGW1-UP; CTK1-UP)
Description of Change: A new hose is being used in the prelubrication lines in order to improve the flow of oil from the turbocharger to the oil pan.
Adaptable To: A new 210-6619 Hose As is being used in the prelubrication lines that are listed in a Table 1. The 210-6619 Hose As is a direct replacement for the former 2V-8571 Hose As. The 210-6619 Hose As has an inside diameter of 19.05 mm (0.750 inch). The former 2V-8571 Hose As has an inside diameter of 12.7 mm (0.50 inch).
Show/hide table
Affected Prelubrication Lines     |
113-4238 Prelubrication Lines     |
113-4239 Prelubrication Lines     |
153-1218 Prelubrication Lines     |
174-4107 Prelubrication Lines     |
190-8848 Prelubrication Lines     |
Show/hide table
Effectivity of the Engines     |
(S/N: 95Y01169-UP)     |
(S/N: 5JD00088-UP)     |
(S/N: 7NJ00882-UP)     |
(S/N: 4EK03719-UP)     |
(S/N: CEY00160-UP)     |
(S/N: 9TG00301-UP)     |
(S/N: 4WD00024-UP)     |
(S/N: 8LD00118-UP)     |
(S/N: 3RC01258-UP)     |
(S/N: BGW00131-UP)     |
(S/N: GET00105-UP)     |
(S/N: CTK00212-UP)     |
Caterpillar Information System:
G3500B Engines Compressor Bypass - Check
Circuit Breaker Harness Assembly {1420} Circuit Breaker Harness Assembly {1420}
3406E, C-10, C-12, C-15, C-16 Truck Engines Refill Capacities and Recommendations
C15 On-highway Engine Inlet and Exhaust Valve Springs - Remove and Install
C15 and C18 Generator Set Engines Cylinder Liner - Remove
C15 and C18 Generator Set Engines Cylinder Liner - Install
3126E and 3126B Commercial and Truck Engines Engine Oil and Filter - Change
2003/12/01 SOLAS Requirements for Fuel Lines {1274}
C11 and C13 Engines Diverter Valve (Coolant) - Remove
C11 and C13 Engines Engine Oil Cooler - Remove
C11 and C13 Engines Crankshaft - Install
C15 On-highway Engine Inlet and Exhaust Valve Guides - Remove and Install
3046 Engine for Caterpillar Built Machines Belt Tension Chart
3044C Industrial Engine and Engines for Caterpillar Built Machines Alternator and Regulator
3044C Industrial Engine and Engines for Caterpillar Built Machines Electric Starting Motor
C11 and C13 Engines Air Compressor Drive Gear - Remove and Install
C27 and C32 Generator Set Engines Camshaft Bearings - Remove
C27 and C32 Generator Set Engines Camshaft Bearings - Install
C11 and C13 Engines Diverter Valve (Coolant) - Install
2003/08/01 Diagnosis of Failure of Exhaust Valve {1105}
G3406 Engines Camshaft
C11 and C13 Engines Precooler - Remove
3408E and 3412E Engines for Caterpillar Built Machines Cylinder Block
C11 and C13 Engines Precooler - Install