Cylinder Liner - Install
安装步骤
Show/hide table
| 需要的工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件名称 | 数量 |
| B | 2P-8260 | 缸套安装工具 | 1 |
| C | 5P-3975 | 橡胶润滑剂 | 1 |
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 检查缸套突出量。 请参阅测试和调整, "缸套突出量 - 检查"。
- 将缸套密封 (3) 安装在缸套 (1) 上。
Show/hide table
 | |
| 图 1 | g01111530 |
- 缸套孔表面和缸套密封件上 (3) 使用工具 (C) 。
注: 不要使用机油、润滑脂或 Vaseline 作为缸套下密封的橡胶润滑剂。
- 把加注口带箍 (2) 在清洁的发动机机油中浸泡一会儿。 然后立刻将加注口带箍安装到缸套上。
- 使用工具 (B) 来把缸套 (1) 安装到缸体中。 确保一切与缸套凸出量有关的标记都要校准。
End By: 安装活塞和连杆。 请参阅 拆解和组装, "活塞和连杆 - 安装"。
Caterpillar Information System:
3126E and 3126B Commercial and Truck Engines Engine Oil and Filter - Change
2003/12/01 SOLAS Requirements for Fuel Lines {1274}
C11 and C13 Engines Diverter Valve (Coolant) - Remove
C11 and C13 Engines Engine Oil Cooler - Remove
C11 and C13 Engines Crankshaft - Install
C15 On-highway Engine Inlet and Exhaust Valve Guides - Remove and Install
C15 On-highway Engine Inlet and Exhaust Valves - Remove and Install
C15 On-highway Engine Inlet and Exhaust Valve Seat Inserts - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines Crankshaft - Remove
SPP101 Skid Mounted Pumper Engine Crankcase Breather - Clean
2003/08/01 A Previous High Temperature Locknut is Used in Engine Exhaust System Groups {7553}
G3406 Engines Ignition Transformer
C15 and C18 Generator Set Engines Cylinder Liner - Remove
C15 On-highway Engine Inlet and Exhaust Valve Springs - Remove and Install
3406E, C-10, C-12, C-15, C-16 Truck Engines Refill Capacities and Recommendations
Circuit Breaker Harness Assembly {1420} Circuit Breaker Harness Assembly {1420}
G3500B Engines Compressor Bypass - Check
2003/08/01 New Hose Improves the Drainage of Oil from the Turbocharger During a Continuous Prelube Cycle {1052}
3046 Engine for Caterpillar Built Machines Belt Tension Chart
3044C Industrial Engine and Engines for Caterpillar Built Machines Alternator and Regulator
3044C Industrial Engine and Engines for Caterpillar Built Machines Electric Starting Motor
C11 and C13 Engines Air Compressor Drive Gear - Remove and Install
C27 and C32 Generator Set Engines Camshaft Bearings - Remove
C27 and C32 Generator Set Engines Camshaft Bearings - Install