Electronic Control Module - Remove and Install
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
- 将软管 (2) 和 ( 4) 从电子控制模块上断开。
- 立即堵住所有开口。
- 松开六角头固定螺钉 ( 3) 直至可以断开发动机配线线束 ( 1)。
- 断开发动机配线线束 ( 1)。
- 松开六角头固定螺钉 ( 5) 直至可以断开机器配线线束 ( 6)。
- 断开电磁阀配线线束 ( 6) 。
Show/hide table
图 2 g00522336 - 拆除下列项: 四个螺栓 (8) , 八个垫圈 (9) , 八个橡胶安装架 ( 11), 带 (7) 和 四个隔套。
- 拆下电子控制模块 ( 10)。
Show/hide table
图 1 | g00522333 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将电子控制模块 ( 10) 放置到缸体上。
- 安装下列项: 四个隔套, 八个橡胶安装架 ( 11), 四垫个圈 ( 9), 带 (7) 和 四个螺栓 (8) 。
Show/hide table
图 4 g00522333 - 连接发动机配线线束 ( 1) 并拧紧六角头固定螺钉 ( 3)。
- 连接机器配线线束 ( 6) 并将六角头固定螺钉 ( 5) 拧紧至下列扭矩
2.25 ± 0.25 N·m (20 ± 2 lb in) 。 - 将软管 (2) 和软管 ( 4) 连接到电子控制模块 ( 10) 上。
注: 关于电子控制模块拆解和组装的更多信息,请参阅 电子故障诊断与排除手册 , RENR1283。
Show/hide table
图 3 | g00522336 |
Caterpillar Information System:
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Gear - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Camshaft Gear - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Assemble
3406C (PEEC III) Truck Engines Cooling System
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Disassemble
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal Carrier - Remove and Install
3500 Spark Ignited Engines Piston and Rings
3176C and 3196 Engines For Caterpillar Built Machines Turbocharger - Install
3176C and 3196 Engines For Caterpillar Built Machines Turbocharger - Remove
3114, 3116 and 3126 MUI Engine Governors Governor (Type I) - Disassemble
3114, 3116 and 3126 MUI Engine Governors Fuel Transfer Pump
3176C and 3196 Engines For Caterpillar Built Machines Camshaft Position Sensor - Remove and Install
3500 Spark Ignited Engines Valve Mechanism
3406E On-Highway Engine Engine Oil Filter Base - Assemble
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Position Sensor - Remove and Install
3176C and 3196 Industrial Engines Compression Brake - Install
G3500B Engines Cylinder Head Valves
3406E On-Highway Engine Engine Oil Pump - Assemble
3176C and 3196 Engines For Caterpillar Built Machines Connecting Rod Bearings - Remove
3176C and 3196 Engines For Caterpillar Built Machines Connecting Rod Bearings - Install
C-10 and C-12 Engines Gear Group (Front) - Remove
P16, P20, P25, P28, P40 and P60 Pulverizers Gerotor Motor - Remove
3406E On-Highway Engine Fuel Transfer Pump - Install
3500 Spark Ignited Engines Cylinder Head