Crankshaft Gear - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 1U-6400 | 三爪拉拔器 | 1 |
开始:
- 拆下曲轴。 请参阅 拆解和组装, "曲轴 - 拆卸" 。
- 使用工具 (A) 将曲轴齿轮 ( 2) 从曲轴 (1) 上拆下。
- 拆卸驱动销 (3) 。
Show/hide table
图 1 | g01022856 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
B | 6V-2098 | 压套管 | 1 |
C | 8H-8581 | 仪表 | 1 |
- 安装驱动销 (3) 。
Show/hide table
操作已经加热的零件时要坚持戴防护手套。
- 加热曲轴齿轮 (2)。
- 将曲轴齿轮 (2) 安装到曲轴 ( 1) 端部。 确保曲轴齿轮 ( 2) 内的卡槽对准驱动销 ( 3) 。
Show/hide table
图 3 g01066239 - 用 工具 (B) 将曲轴齿轮 ( 2) 抵着曲轴 (1) 轴肩定位。
- 用工具 (C) 确保曲轴齿轮 ( 2) 抵着曲轴轴肩定位。
注: 用工具 (C) 检查三个位置的曲轴齿轮。
Show/hide table
图 2 | g01066237 |
结束:
- 安装曲轴。 请参阅 拆解和组装, "曲轴 - 安装" 。
Caterpillar Information System:
3176C and 3196 Engines For Caterpillar Built Machines Camshaft Gear - Remove and Install
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Assemble
3406C (PEEC III) Truck Engines Cooling System
3176C and 3196 Engines For Caterpillar Built Machines Accessory Drive - Disassemble
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Rear Seal Carrier - Remove and Install
3500 Spark Ignited Engines Piston and Rings
3176C and 3196 Engines For Caterpillar Built Machines Turbocharger - Install
3176C and 3196 Engines For Caterpillar Built Machines Turbocharger - Remove
3114, 3116 and 3126 MUI Engine Governors Governor (Type I) - Disassemble
3114, 3116 and 3126 MUI Engine Governors Fuel Transfer Pump
3176C and 3196 Engines For Caterpillar Built Machines Camshaft Position Sensor - Remove and Install
3114, 3116 and 3126 MUI Engine Governors Dual Horsepower (Type VII)
3176C and 3196 Industrial Engines Electronic Control Module - Remove and Install
3500 Spark Ignited Engines Valve Mechanism
3406E On-Highway Engine Engine Oil Filter Base - Assemble
3176C and 3196 Engines For Caterpillar Built Machines Crankshaft Position Sensor - Remove and Install
3176C and 3196 Industrial Engines Compression Brake - Install
G3500B Engines Cylinder Head Valves
3406E On-Highway Engine Engine Oil Pump - Assemble
3176C and 3196 Engines For Caterpillar Built Machines Connecting Rod Bearings - Remove
3176C and 3196 Engines For Caterpillar Built Machines Connecting Rod Bearings - Install
C-10 and C-12 Engines Gear Group (Front) - Remove
P16, P20, P25, P28, P40 and P60 Pulverizers Gerotor Motor - Remove
3406E On-Highway Engine Fuel Transfer Pump - Install