Final Drive Sprocket - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 8S-7640     | Stand     | 2     |
8S-7611 | Tube     | 2     | |
8S-7615 | Pin     | 2     | |
B     | 138-7574     | Link Bracket     | 1     |
Start By:
- Separate the track assembly. Refer to Disassembly and Assembly, "Track - Separate" in this manual.
- Lift the side of the machine, and install Tooling (A) under the frame, as shown.
Show/hide table
Illustration 1 | g00371733 |
Note: Adjust the height of Tooling (A) so that there is sufficient clearance between the sprocket and the track links for the removal of the sprocket.
- Remove 22 bolts (1) that hold the sprocket to the final drive.
Show/hide table
Illustration 2 | g00371752 |
- Fasten Tooling (B) and a hoist to sprocket (2), as shown. Remove the sprocket. The weight of the sprocket is 60 kg (130 lb).
Show/hide table
Illustration 3 | g00371812 |
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 8S-7640     | Stand     | 2     |
8S-7611 | Tube     | 2     | |
8S-7615 | Pin     | 2     | |
B     | 138-7574     | Link Bracket     | 1     |
- Thoroughly clean the mating surfaces of the sprocket and final drive prior to installation of the sprocket.
- Fasten Tool (B) and a hoist to sprocket (2), and put the sprocket in position on the final drive.
Show/hide table
Illustration 4 | g00371812 |
- Put a thin coat of 9S-3263 Thread Lock Compound on the threads of 22 bolts (1) that hold the sprocket to the final drive. Install bolts (1). Tighten the bolts to a torque of 270 ± 40 N·m (200 ± 30 lb ft).
Show/hide table
Illustration 5 | g00371752 |
- Raise the machine, and remove Tooling (A) from the frame.
Show/hide table
Illustration 6 | g00371733 |
End By: Connect the track assembly. Refer to Disassembly and Assembly, "Track - Connect" in this manual.
Caterpillar Information System:
315B Excavator Machine Systems Pilot Valve (Travel) - Install
307B Excavator Rubber Segment Track Operation - If Equipped
315B and 315B L Excavator Supplement For 3046 Engine Oil Pan - Remove and Install
315B Excavator Machine Systems Recoil Spring - Assemble
307B Excavator Implement Flow Control
307B Excavator Leaving the Machine
330B Excavator Hydraulic System Piston Pump (Main) - Test
315B Excavator Machine Systems Main Hydraulic Pump - Assemble
M312 Excavator Machine System Bucket - Ditch Cleaning, Adjustable
M312 Excavator Machine System Bucket - Ditch Cleaning, Rigid
345B Excavator Shipping Specifications
307B Excavator Implement Control Pedal - If Equipped
315B Excavator Machine Systems Pilot Valve (Travel) - Disassemble
M312 Excavator Machine System Bucket - Ditch Cleaning, Rigid
322B Excavator Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
315B Excavator Machine Systems Pilot Valve (Travel) - Assemble
322B Excavator Hydraulic System Travel Motor - Test - Measurement of Case Drain Oil
315B and 315B L Excavator Supplement For 3046 Engine Governor Control Motor - Remove and Install
322B Excavator Hydraulic System Pump Control (Negative Flow) - Adjust
M312 Excavator Machine System Bucket Linkage
315B Excavator Machine Systems Solenoid Valve (Swing Priority) - Remove and Install
315B and 315B L Excavator Supplement For 3046 Engine Flywheel and Ring Gear - Remove and Install
315B and 315B L Excavator Supplement For 3046 Engine Flywheel Ring Gear - Remove and Install
315B Excavator Machine Systems Boom Lighting - Remove and Install