Radiator Guard - Install
Installation Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 138-7574 | Link Bracket | 4 |
- Install Tooling (A), as shown.
Show/hide table
 | |
| Illustration 1 | g00753460 |
- Attach a suitable hoist and lifting chains to Tooling (A), as shown.
- Use the hoist in order to carefully install radiator guard (32). The weight of the radiator guard is 1270 kg (2800 lb).
Show/hide table
 | |
| Illustration 2 | g00850317 |
- Install four bolts (31) and the washers. Repeat this procedure for the opposite side.
Show/hide table
 | |
| Illustration 3 | g00850314 |
View From Below The Counterweight | |
- Install bolt (30) and the washer. Repeat this procedure for the opposite side.
Show/hide table
 | |
| Illustration 4 | g00850310 |
- Install bolt (29) and the washer.
Show/hide table
 | |
| Illustration 5 | g00850307 |
Left Side View | |
- Install bolt (28) and the washer.
Show/hide table
 | |
| Illustration 6 | g00850304 |
Right Side View | |
- Remove the hoist, lifting chains, and Tooling (A) .
- Connect hose assembly (27) .
Show/hide table
 | |
| Illustration 7 | g00850300 |
- Connect hose assembly (22) to top radiator tank (24) .
Show/hide table
 | |
| Illustration 8 | g00850296 |
- Connect hose assembly and tighten clamp (23) .
- Connect hose assembly and tighten two clamps (25) .
- Slide the rubber sleeve toward the rear of the machine in order to connect the tube assembly. Tighten two clamps (26) .
- Connect electrical connector (20) .
Show/hide table
 | |
| Illustration 9 | g00850293 |
- Install bolt (21), the washer, and the clamp.
- Connect hose assemblies (17), (18), and (19) .
Show/hide table
 | |
| Illustration 10 | g00850292 |
- Close access door (16) .
Show/hide table
 | |
| Illustration 11 | g00850288 |
Typical Example | |
- Connect three hose assemblies (15) .
Show/hide table
 | |
| Illustration 12 | g00850281 |
- Connect two tube assemblies (14) .
Show/hide table
 | |
| Illustration 13 | g00850276 |
- Tighten two clamps (13) .
- Slide sleeve (11) in order to connect tube assembly (10). Tighten four clamps (12). Repeat this procedure for the opposite side.
Show/hide table
 | |
| Illustration 14 | g00850273 |
- Install plate (9) .
Show/hide table
 | |
| Illustration 15 | g00850272 |
- Install hose assembly (7). Tighten two clamps (6) .
- Install bolt (8) and the washer. Repeat this procedure for the opposite side.
- Attach a suitable hoist and lifting slings to cover (4), as shown.
Show/hide table
 | |
| Illustration 16 | g00850262 |
Show/hide table
 | |
| Illustration 17 | g00850261 |
- Use the hoist in order to install cover (4). The weight of the cover is 45 kg (100 lb).
- Install bolts (1) and (2), the spacers, and the washers finger tight.
- Remove lifting slings (3) and (5) .
- Tighten bolts (1) and (2) .
- Fill the hydraulic tank to the proper level. Refer to the appropriate Operation and Maintenance Manual for the correct procedure.
End By: Install the front and rear hood panels. Refer to Disassembly and Assembly, "Hood Panels (Front and Rear) - Install" for the machine that is being serviced.
Caterpillar Information System:
CB-634D Paving Compactor Battery - Clean/Check
570B Wheel Harvester and 580B Wheel Harvester Engine Supplement Water Pump - Remove and Install - Engine in Chassis
14H Motor Grader Plate Locations and Film Locations
2003/07/14 New Service Parts Are Available for Extreme Brake Applications {4011, 4255}
16H Motor Grader Specifications
988G Wheel Loader Engine Supplement Radiator Guard - Remove
MT735, MT745, MT755 and MT765 Agricultural Tractors Engine Supplement Drive Shaft - Remove and Install
570B Wheel Harvester and 580B Wheel Harvester Engine Supplement Water Temperature Regulator - Remove and Install - Engine in Chassis
PM-465 Cold Planer Fuel System - Prime
533 Wheel Feller Buncher and 543 Wheel Feller Buncher Power Train Pressure Switch (Forward, Reverse, and Creep Mode)
777D HAA Off-Highway Truck Engine Air Filter Secondary Element - Replace
988G Wheel Loader Engine Supplement Water Temperature Regulator - Remove and Install - Engine In Chassis
773E Off-Highway Truck And 775E Off-Highway Truck Assembly Procedure{7000, 7006, 7960} 773E Off-Highway Truck And 775E Off-Highway Truck Assembly Procedure{7000, 7006, 7960}
120H and 135H Motor Graders Power Train Air Conditioner
533 Wheel Feller Buncher and 543 Wheel Feller Buncher Power Train Pressure Reducing Valve (Speed Control Regulator)
PM-465 Cold Planer Fuel System Primary Filter - Clean/Inspect/Replace
CB-634D Paving Compactor Belts - Inspect/Adjust/Replace
2001/12/17 Correction to Specifications , "Steering Gear" {4310}
533 Wheel Feller Buncher and 543 Wheel Feller Buncher Power Train Transmission Gearbox
CB-534D, CB-534D XW and CB-564D Vibratory Compactors Machine Systems Water Spray Pump - Disassemble
CB-534D, CB-534D XW and CB-564D Vibratory Compactors Machine Systems Water Spray Pump - Assemble
2001/12/17 A New Retaining Clip will Improve the Alignment of the Hose Assembly on the Condenser {1374, 1808, 5057, 7320}
TH103 Telehandler Hydraulic System Pressure for Pump and Relief Valve (Main) - Test and Adjust
533 Wheel Feller Buncher and 543 Wheel Feller Buncher Power Train Drive Shaft (Machine)