Stabilizer - Install
Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 180-3034 | Jack Stand Gp | 1 |
| B | 174-7525 | Support Stand | 1 |
| C | 6V-6146 | Load Leveler | 1 |
| D | 1U-8261 | Nylon Lifting Sling | 2 |
| E | 180-3033 | Jack Stand Gp | 1 |
- Install tooling (D) around stabilizer frame (15). In order to balance stabilizer frame (15), make sure that tooling (D) is attached toward the rear of the stabilizer frame, as shown. Attach tooling (D) to tool (C) and to a suitable hoist. Slowly lift stabilizer frame (15) off the cribbing and tool (E). The weight of stabilizer frame (15) is 540 kg (1190.5 lb).
Show/hide table
 | |
| Illustration 1 | g00743212 |
Show/hide table
 | |
| Illustration 2 | g00743387 |
- Carefully move stabilizer frame (15) toward the machine. Feed harness (16) and hoses (11) through the hole in stabilizer frame (15) .
Show/hide table
 | |
| Illustration 3 | g00743218 |
- Position frame (15) onto the machine and install eight bolts (12), sixteen washers (13), and eight nuts (14). Tighten the bolts to 530 ± 70 N·m (391 ± 52 lb ft).
Show/hide table
 | |
| Illustration 4 | g00743399 |
- Connect three hoses (11) and tighten retaining nuts (10). Connect four electrical connectors (8) and install two new cable straps (9) .
Show/hide table
 | |
| Illustration 5 | g00743075 |
- Install cover plate (7), four washers (6), and four bolts (5) .
Show/hide table
 | |
| Illustration 6 | g00742994 |
- Raise the boom and remove the upper section of tool (B) .
Show/hide table
 | |
| Illustration 7 | g00740249 |
- Slowly lower the boom onto tool (A) and remove the base of tool (B). Install shims (4), buffer pad (3), four washers (2) and four bolts (1) .
Show/hide table
 | |
| Illustration 8 | g00740250 |
Caterpillar Information System:
Machine Security System Engine Does Not Crank and Status Indicator Is Green
2000/09/25 Correction to Electrical System Schematic SENR5897 {7566}
247, 257, 267, 277 and 287 Multi Terrain Loaders and 216, 226, 228, 232, 236, 242, 246, 248, 252 and 262 Skid Steer Loaders Auxiliary Hydraulic Electronic Control System MID 106 - CID 0168 - FMI 04
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Control Valve (Boom)(Mechanically Operated)
416D Backhoe Loader Hydraulic and Steering System Control Valve (Swing)
IT62G Series II Integrated Toolcarrier Engine Starting with Air Inlet Heater
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Control Valve (Backhoe Bucket)(Mechanically Operated)
247, 257, 267, 277 and 287 Multi Terrain Loaders and 216, 226, 228, 232, 236, 242, 246, 248, 252 and 262 Skid Steer Loaders Auxiliary Hydraulic Electronic Control System MID 106 - CID 0168 - FMI 03
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Control Valve (Stick)(Mechanically Operated)
797 Off-Highway Truck Hydraulic System Hydraulic Tank
416D Backhoe Loader Hydraulic and Steering System Bank Valve (Backhoe)
2000/09/25 An Improved Tilt Cylinder Guard is Now Available {5104}
AP-1050B and BG-245C Asphalt Pavers Parking Brake Control
IT62G Series II Integrated Toolcarrier Engine Starting with Jump Start Cables
TH62, TH63, TH82, TH83 and TH103 Telehandlers Power Train Differential and Bevel Gear - Disassemble
2000/10/09 Correction to the Adjustment Procedure of the Swing Dampener for the Grapple {5569}
Machine Security System Engine Does Not Start and Status Indicator Is Continuously Red
AP-1050B and BG-245C Asphalt Pavers Service Brake Control
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Engine Starting with Auxiliary Start Receptacle
AP-1050B and BG-245C Asphalt Pavers Propel Control
2000/10/02 Repair Parts Available for Alternator R-Terminal {1405}
938G Wheel Loader and IT38G Integrated Toolcarrier Power Train Gear Pump (Axle Oil Cooler)
TH62, TH63, TH82 and TH83 Telehandlers Hydraulic System Bank Valve
AP-1050B and BG-245C Asphalt Pavers Maximum Propel Speed Potentiometer