561N, 572R Series II and 572R Pipelayers and D10R, D11R, D5M, D5N, D6M, D6N, D6R, D6R Series II, D7R, D7R Series II and D8R Series II Track-Type Tractors Power Train Electronic Control System Caterpillar


MID 113 - CID 0694 - FMI 06

Usage:

D6R 1RW
Conditions Which Generate This Code:


Illustration 1g00633940
Schematic of the Modulating Valve for Speed 2 (Number 4)

This diagnostic code is for the Modulating Valve for Speed 2 (Number 4).

See Systems Operation, "Solenoid Valves" for help with the identification of the locations of the solenoids.

This diagnostic code is recorded when the current of the solenoid circuit is above normal.

Note: Ensure that CID 0694 FMI 06 for the solenoid is on hold and that the diagnostic code indicator shows "SERV CODE".

Test Step 1. CHECK THE SOLENOID AND THE INTERNAL HARNESS OF THE TRANSMISSION.

  1. Turn the key start switch to the ON position.

  2. Ensure that the diagnostic code for the solenoid is on hold.

  3. Observe the status of the diagnostic code indicator.

  4. At the transmission case, disconnect the machine harness from the internal harness for the transmission.

Expected Result:

"SERV CODE" is NOT showing when the internal harness for the transmission is disconnected.

Results:

  • YES - "SERV CODE" is NOT showing when the internal harness for the transmission is disconnected. The circuit is correct. The solenoid or the internal harness for the transmission has failed. Proceed to Test Step 2.

  • NO - "SERV CODE" is showing when the internal harness for the transmission is disconnected. The diagnostic code remains. Proceed to Test Step 3.

Test Step 2. CHECK THE RESISTANCE OF THE SOLENOID.

  1. Within the transmission case, disconnect the internal harness for the transmission from the solenoid that is suspected.

  2. At the solenoid, measure the resistance between the two contacts of the connector for the solenoid.

Expected Result:

The resistance should be greater than 5 ohms.

Results:

  • OK - The resistance is greater than 5 ohms.

    Repair: The resistance of the solenoid is correct. The internal harness for the transmission is failed. In the internal harness for the transmission, the wire for the signal to the solenoid is shorted to the return circuit for the solenoid (wire 975-WH(White)) or to the frame ground. Repair the internal harness for the transmission or replace the internal harness for the transmission .

    STOP

  • NOT OK - The resistance is not greater than 5 ohms.

    Repair: The solenoid has failed. Replace the solenoid.

    STOP

Test Step 3. CHECK THE SIGNAL CIRCUIT FOR THE SOLENOID FOR A SHORT TO GROUND.

  1. At the transmission case, the machine harness remains disconnected from the internal harness for the transmission . Turn the key start switch to the OFF position.

  2. Disconnect the machine harness from the solenoid.

  3. Disconnect the machine harness connectors J1 and J2 from the ECM.

  4. At machine harness connector J1 or J2, measure the resistance from the solenoid signal contact to all possible sources of ground. The possible ground sources are contact J1-2, contact J1-5, contact J1-7, contact J1-15, contact J1-16, contact J2-3 and frame ground.

Expected Result:

Each resistance should be greater than 5000 ohms.

Results:

  • OK - Each resistance is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 4.

  • NOT OK - Each resistance is not greater than 5000 ohms.

    Repair: There is a short in the machine harness. The short is between the wire for the signal to the solenoid and the circuit that has a low resistance measurement. Repair the machine harness or replace the machine harness.

    STOP

Test Step 4. DETERMINE IF THE DIAGNOSTIC CODE IS STILL ACTIVE.

  1. Inspect the contacts and clean the contacts of the harness connectors.

  2. Reconnect all harness connectors.

  3. Turn the key start switch to the ON position.

  4. Enter service mode of the Caterpillar Monitoring System and clear all inactive diagnostic codes.

  5. Operate the machine.

  6. Stop the machine and place the parking brake switch in the ON position.

  7. Determine if the CID 0694 FMI 06 for the solenoid is present.

Expected Result:

CID 0694 FMI 06 for the solenoid is present. "SERV CODE" is showing.

Results:

  • YES - CID 0694 FMI 06 for the solenoid is present. "SERV CODE" is showing.

    Repair: Exit this procedure and perform the diagnostic code procedure again. If the problem persists, the ECM may have failed. Prior to replacing an ECM, always contact your dealership's Technical Communicator for possible consultation with Caterpillar. This consultation may greatly reduce repair time. See the Testing and Adjusting, "Electronic Control Module (ECM) - Replace".

    STOP

  • NO - CID 0694 FMI 06 for the solenoid is not present. "SERV CODE" is not showing.

    Repair: The problem does not exist at this time. The initial problem was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation.

    STOP

Caterpillar Information System:

TH103, TH62, TH63, TH82 and TH83 Telehandlers Longitudinal Stability Indicator System General Information
AP-1050B and BG-245C Asphalt Pavers Pump Drive Oil Sample - Obtain
561N, 572R Series II and 572R Pipelayers and D10R, D11R, D5M, D5N, D6M, D6N, D6R, D6R Series II, D7R, D7R Series II and D8R Series II Track-Type Tractors Power Train Electronic Control System MID 113 - CID 0694 - FMI 05
AP-1050B and BG-245C Asphalt Pavers Pump Drive Oil - Change
HH45 Harvester Head, HH55 Harvester Head, HH65 Harvester Head and HH75 Harvester Head Harvester Head System Pressure - Test/Adjust
AP-1050B and BG-245C Asphalt Pavers Power Train Oil Filters - Replace
561N, 572R Series II and 572R Pipelayers and D10R, D11R, D5M, D5N, D6M, D6N, D6R, D6R Series II, D7R, D7R Series II and D8R Series II Track-Type Tractors Power Train Electronic Control System MID 113 - CID 0694 - FMI 03
561N, 572R Series II and 572R Pipelayers and D10R, D11R, D5M, D5N, D6M, D6N, D6R, D6R Series II, D7R, D7R Series II and D8R Series II Track-Type Tractors Power Train Electronic Control System MID 113 - CID 0693 - FMI 07
561N, 572R Series II and 572R Pipelayers and D10R, D11R, D5M, D5N, D6M, D6N, D6R, D6R Series II, D7R, D7R Series II and D8R Series II Track-Type Tractors Power Train Electronic Control System MID 113 - CID 0693 - FMI 06
561N, 572R Series II and 572R Pipelayers and D10R, D11R, D5M, D5N, D6M, D6N, D6R, D6R Series II, D7R, D7R Series II and D8R Series II Track-Type Tractors Power Train Electronic Control System MID 113 - CID 0693 - FMI 05
561N, 572R Series II and 572R Pipelayers and D10R, D11R, D5M, D5N, D6M, D6N, D6R, D6R Series II, D7R, D7R Series II and D8R Series II Track-Type Tractors Power Train Electronic Control System MID 113 - CID 0693 - FMI 03
Caterpillar Monitoring System Alert Indicator Is Always Flashing
AP-1050B and BG-245C Asphalt Pavers Track Roller Bearings - Inspect
AP-1050B and BG-245C Asphalt Pavers Track Roller Bearings - Lubricate
AP-1050B and BG-245C Asphalt Pavers Tracks - Inspect
TH103, TH62, TH63, TH82 and TH83 Telehandlers Longitudinal Stability Indicator System Switch (Boom) - Adjust
3500B Engines for Caterpillar Built Machines Air Inlet and Exhaust System Operation
AP-1050B and BG-245C Asphalt Pavers Truck Hitch - Lubricate - If Equipped
IT28G and IT38G Integrated Toolcarriers and 924G, 924GZ, 928G and 938G Wheel Loaders Power Train Electronic Control System Other Features
TH103, TH62, TH63, TH82 and TH83 Telehandlers Longitudinal Stability Indicator System Sensor
TH103, TH62, TH63, TH82 and TH83 Telehandlers Longitudinal Stability Indicator System Switch (Boom)
TH103, TH62, TH63, TH82 and TH83 Telehandlers Longitudinal Stability Indicator System Display Module
2001/06/11 The Maximum Payload Speed Manager Feature of the VIMS Truck Payload System with VIMS 9.62X and 10.X Classes of Onboard Software {7494, 7601}
2000/09/11 Explanation of Automatic Lubrication System for VIMS {7540, 7601}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.