Front Track Roller Frame - Install
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 8S-9906     | Ratchet Puller     | 1     |
B     | 8T-5071     | Seal Guard     | 1     |
C     | FT-1976     | Starter     | 1     |
6V-3009 | Crossbar     | 1     | |
D     | FT-1965     | Driver     | 1     |
- Install bearing (4) and ring (5) in the rear track roller frame.
Show/hide table
Illustration 1 | g00693617 |
Show/hide table
Illustration 2 | g00693618 |
- Make sure that the seal bore that is in the rear track roller frame is clean and free of dirt, oil, and old adhesive.
- Put 7M-7456 Bearing Mount Compound on the seal bore.
- Use Tooling (C) to start seal assembly (6) in the rear track roller frame.
- Use Tooling (D) to seat seal assembly (6) in the rear track roller frame.
Show/hide table
Illustration 3 | g00693621 |
- Put clean SAE 30W oil on the bearing, the ring, and the seal assembly.
- Cut Tooling (B) to a tight fit inside seal assembly (6) when the ends of Tooling (B) make contact.
Show/hide table
Illustration 4 | g00693625 |
- Put Tooling (B) in position in seal assembly (6). Make sure that the back leg of Tooling (B) is in the gap between the seal assembly and the front track roller frame.
- If sleeve (3) was removed, heat the sleeve to a maximum temperature of 175 °C (347 °F). Use temperature resistant gloves to handle the sleeve. Install the sleeve on the front track roller frame.
Show/hide table
Illustration 5 | g00693628 |
- Fasten a hoist and a suitable lifting device to front track roller frame (2) .
Show/hide table
Illustration 6 | g00693630 |
- Install the front track roller frame in the rear track roller frame. Make sure that sleeve (3) is within 25.4 mm (1.00 inch) of the seal assembly that is in the rear track roller frame.
- Remove Tooling (B) from the seal assembly.
Show/hide table
NOTICE |
---|
Make sure that you use caution when you install the front track roller frame. Damage could occur to the seal assembly in the rear track roller frame. |
- Use Tooling (A) to pull the front track roller frame in position in the rear track roller frame.
- Align the slots in the front track roller frame with retainers (1). Install the retainers.
Show/hide table
Illustration 7 | g00693631 |
- After the track has been adjusted, fill the recoil spring compartment with oil to the correct level.
Note: Refer to Operation and Maintenance Manual, "Recoil Spring Compartment" for the correct filling procedure.
End By: Connect the track. Refer to Disassembly and Assembly, "Track - Connect" for the machine that is being serviced.
Caterpillar Information System:
517 Track-Type Skidder Power Train Front Track Roller Frame - Remove
517 Track-Type Skidder Power Train Sprocket Segment - Remove and Install
980G Wheel Loader Power Train Final Drive, Brake and Wheel - Remove
824G Wheel Dozer, 825G Soil Compactor and 826G Landfill Compactor Hydraulic System Hydraulic Tank and Filter
3176C and 3196 Engines For Caterpillar Built Machines Fuel Manifold - Remove
517 Track-Type Skidder Power Train Track - Connect
517 Track-Type Skidder Power Train Track - Separate
C9 Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
824G , 825G and 826G Landfill Compactor Window Washer Reservoir - Fill
517 Track-Type Skidder Power Train Track Roller - Assemble
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Charge Pump
416C, 426C, 428C, 436C and 438C Backhoe Loaders Axles, Differential and Brakes Drive and Steering Axle (Front)
517 Track-Type Skidder Power Train Recoil Spring - Remove
517 Track-Type Skidder Power Train Recoil Spring - Install
517 Track-Type Skidder Machine Systems Fuel Tank (Fixed Boom) - Remove
517 Track-Type Skidder Power Train Track Adjuster - Remove
517 Track-Type Skidder Power Train Track Adjuster - Install
517 Track-Type Skidder Machine Systems Fuel Tank (Swing Boom) - Install
517 Track-Type Skidder Power Train Track Roller Frame - Remove
517 Track-Type Skidder Machine Systems Fuel Tank (Swing Boom) - Remove
517 Track-Type Skidder Power Train Track Roller Frame - Install
517 Track-Type Skidder Power Train Idler - Disassemble
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Transmission Heater
517 Track-Type Skidder Power Train Idler - Assemble