Vibration Damper and Pulley - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
A     | FT-0915     | 接头     | 1     |
0S-1590 | 螺栓     | 6     | |
5F-7342 | 接头     | 2     | |
5F-7369 | 拉拔器腿     | 2     | |
3H-0465 | 压拉器垫板     | 4     | |
1B-4207 | 全高螺母     | 2     | |
8B-7560 | 垫板     | 1     | |
1P-0820 | 液压拉拔器     | 1     | |
4C-4865 | 手动液压泵     | 1     |
开始:
- 释放驱动皮带张力,然后拆下驱动皮带。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 从曲轴上拆下螺栓 (1) 和垫圈 (2) 。 将隔套 (4) 安装到螺栓 (1) 上。 增加隔套,以便达到垫圈 (2) 和减振器 (3) 之间约 3.18 mm (0.125 in) 的间隙。 安装螺栓 (1) 、垫圈 (2) 和隔套 (4) 。
Show/hide table
图 1 | g00515722 |
- 如图所示,安装工具 (A) 。 从曲轴上松开减振器 (9) 。
Show/hide table
图 2 | g00515749 |
- 从曲轴上拆下工具 (A) 、螺栓 (1) 、垫圈 (2) 、隔套 (4) 和减振器 (3) 。
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 检查减振器有无泄漏和凹痕。 如果出现任一种情况,用新零件更换减振器。
- 将减振器 (1) 在曲轴上放置到位,然后安装垫圈 (2) 和螺栓 (3) 。
注: 安装时,垫圈 (2) 的平面侧必须朝向减振器 (1) 。
Show/hide table
图 3 | g00515758 |
- 将螺栓 (3) 拧紧至扭矩 284 至 340 N·m (210 至 250 lb ft)。 用锤子敲击螺栓 (3) ,然后再次将螺栓拧紧至扭矩 284 至 340 N·m (210 至 250 lb ft)。
End By: 安装驱动皮带并施加正确的张紧力。
Caterpillar Information System:
773D Off-Highway Truck and 775D Quarry Truck Air System and Brakes Control Valve (Hoist)
69D and 769D Off-Highway Truck and 771D Quarry Truck Air System and Brakes Control Valve (Hoist)
3406E On-Highway Engine Crankshaft Rear Seal - Remove
3176C and 3196 Engines For Caterpillar Built Machines Lifter Group - Remove and Install
3412E Engine Supplement for 773D Off-Highway Trucks and 775D Off-Highway Quarry Trucks Refrigerant Accumulator - Remove and Install
D250E Series II and D300E Series II Articulated Trucks Machine Systems Parking Brake - Assemble
3176C and 3196 Engines For Caterpillar Built Machines Rocker Shaft and Pushrod - Install
776D, 777D and 777D HAA Off-Highway Truck/Tractors Air System and Brakes Air Ratio Valve (Front Brake)
D8R Series II Track-Type Tractor Hydraulic System Check Valve
583R Pipelayer Power Train Track Roller Frames
IT14G Integrated Toolcarrier and 914G Wheel Loader Steering System Secondary Steering Pump and Electric Motor
69D and 769D Off-Highway Truck/Tractors and 771D Quarry Truck Hydraulic System Hydraulic Tank (Hoist and Brake)
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0642 FMI 03 Solenoid Valve 2 (Direction Clutch) Voltage Above Normal - Test
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0643 FMI 03 Solenoid Valve 3 (Direction Clutch) Voltage Above Normal - Test
69D and 769D Off-Highway Truck and 771D Quarry Truck Air System and Brakes Air/Hydraulic Cylinder (Front Caliper)
3412E Engine Supplement for 773D Off-Highway Trucks and 775D Off-Highway Quarry Trucks Refrigerant Compressor - Remove and Install
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0644 FMI 03 Solenoid Valve 4 (Speed Clutch) Voltage Above Normal - Test
AP-1055B and BG-2455C Asphalt Pavers Time Delay Relay Control (Leveling)
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0645 FMI 03 Solenoid Valve 5 (Speed Clutch) Voltage Above Normal - Test
583R Pipelayer Power Train Idlers (Track)
24H Motor Grader Transmission Electronic Control System And Hydraulic Calibrations CID 0646 FMI 03 Solenoid Valve 6 (Speed Clutch) Voltage Above Normal - Test
69D and 769D Off-Highway Truck and 771D Quarry Truck Air System and Brakes Electric Drive Pump (Secondary Steering and Brake Release)
3406E and 3456 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Install
3176C and 3196 Engines For Caterpillar Built Machines Water Outlet Manifold - Remove