Steering System Check
- Raise the machine so that both belts are 20 to 30 cm (8 to 12 inch) off the ground.
- Check the charge oil pressure. Make sure that the pressure is 2470 ± 170 kPa (358 ± 25 psi). Refer to Systems Operation/Testing and Adjusting, "Steering System Charge Oil Pressure Test".
- Mark each drive wheel so the revolutions can be counted.
- Engage the parking brake.
- Start the engine. Run the engine at high idle.
- Warm the oil to 60°C (140°F).
- Move the transmission control lever to the NEUTRAL position.
- Rotate the steering wheel to the FULL RIGHT TURN position.
- Hold the steering wheel in this position.
- Count the number of revolutions of each drive wheel in one minute.
- The difference in the revolutions should be between 30 and 34 revolutions.
- Check the pilot valve oil pressure.
- The pressure reading should be at least 1375 kPa (200 psi).
- Check the steering pump oil pressure.
- The pressure reading should be less than 10000 kPa (1450 psi). Refer to Systems Operation/Testing and Adjusting, "Steering Pump High Pressure Cutoff Pressure Test" for the locations of the pressure taps.
- Rotate the steering wheel to the FULL LEFT TURN position.
- Hold the steering wheel in this position.
- Repeat Steps 10 through 12.
- If the measurements from Steps 10 and 12 are not within specifications, there is excessive leakage in the system.
Caterpillar Information System:
583R Pipelayer Power Train Steering Clutches and Brakes
527 Track-Type Skidder Electronic Monitoring System (EMS)
3126 Truck Engine Engine Oil Temperature Sensor
527 Track-Type Skidder Ether Starting Aid - If Equipped
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Cable Connections
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Master Cylinder - Remove and Install
527 Track-Type Skidder Battery Disconnect Switch
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Battery - Replace
773D Off-Highway Truck and 775D Quarry Truck Transmission Planetary
3176C and 3196 Engines for Caterpillar Built Machines Engine Design
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Module - Replace
527 Track-Type Skidder Product Identification Number, Serial Number and EU's CE Plate Locations
527 Track-Type Skidder Backup Alarm
784C and 785C Off-Highway Trucks Machine Systems Cab - Remove
527 Track-Type Skidder Power Train Bevel and Transfer Gears
527 Track-Type Skidder Power Train Drive Shaft
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Front Wheel, Bearing and Duo-Cone Seal - Remove
784C, 785C and 785C HAA Off-Highway Truck Air System and Brakes Air Control Valve (Pulled Unit)
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Off-Board Service Tool
D250E Series II and D300E Series II Articulated Trucks Power Train Retarder Hydraulic Control Valve - Assemble
773D Off-Highway Truck and 775D Quarry Truck Transfer Gears
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Hydraulic Caliper Service Brake - Install
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Front Wheel, Bearing and Duo-Cone Seal - Install
D250E Series II and D300E Series II Articulated Trucks Power Train Retarder Solenoid Control Valve - Remove