Final Drive, Steering Clutch and Brake - Install
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | FT-1952     | Axle Removal Tool     | 1     |
B     | 8T-3207     | Lift Bracket     | 1     |
1A-5405 | Bolt 5/8 inch - 11 × 5 inch long     | 2     | |
1D-4720 | Nut 5/8 inch - 11     | 2     | |
5P-8247 | Washer 5/8 inch     | 4     |
- Inspect all of the O-ring seals for damage. Replace the damaged O-ring seals.
- Fasten a hoist, and install Tooling (B) on the final drive. If necessary, make an adjustment to Tooling (B) in order to place the final drive and the steering clutch and brake in a level position.
Show/hide table
Illustration 1 | g00505145 |
Show/hide table
Illustration 2 | g00505146 |
- Place the final drive and the steering clutch and brake in position on the machine.
- Install two bolts (5) that hold the steering clutch and brake.
- Install 26 bolts (3) that hold the final drive and the steering clutch and brake in position. Remove Tooling (B) .
- Place SAE 30W oil on the threads of the two bolts for the segment. Install the bolts so that the head of the bolts are against the segment and so that the washers and the nuts are against the final drive.
- Tighten the nuts to a torque of 175 ± 40 N·m (130 ± 30 lb ft). Tighten the nuts 1/3 of a turn more.
- Use Tooling (A) and install the inner axle. Remove Tooling (A) .
Show/hide table
Illustration 3 | g00505143 |
- Use Tooling (A) and install the outer axle. Remove Tooling (A) .
- Place the O-ring seal in position on the cover and install the cover on the final drive.
- Turn the final drive until drain plug (1) is toward the bottom. Fill the final drive with oil until the oil is to the bottom of the drain plug hole. Refer to the Operation And Maintenance Guide for the correct type of oil and the capacity.
End By: Connect the track.
Caterpillar Information System:
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Service and Parking Brake (Rear) - Install
789C Off-Highway Truck/Tractor Air System and Brakes Relay Valve (Brake Air)
836G Landfill Compactor and 834G Wheel Dozer Transmission Oil Level - Check
G3B, K3A and L3A Denso Alternators T4 Alternator Drive System - Check
3408E and 3412E Industrial Engines Unit Injector
836G Landfill Compactor and 834G Wheel Dozer Transmission Oil - Change
784C and 785C Off-Highway Trucks Machine Systems Traction Control Valve - Install
3406C Engines for Caterpillar Built Machines Accessory Drive
836G Landfill Compactor and 834G Wheel Dozer Lift Cylinder Upper Trunnion Bearing - Lubricate
836G Landfill Compactor and 834G Wheel Dozer Steering Cylinder Bearings - Lubricate
784C and 785C Off-Highway Trucks Machine Systems Traction Control Valve - Remove
69D, 769D , 773D, 773E, 776D, 777D, 784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Braking System Electronic Control Module (ECM)
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0041 FMI 04 Sensor Power Supply (8 DCV) Voltage Below Normal - Test
G3B, K3A and L3A Denso Alternators T5 Alternator Current - Test
3406C Engines for Caterpillar Built Machines Engine Support (Front)
793C and 793C XQ Off-Highway Truck Air System and Brakes Inverter Valve (Secondary Brake)
3408E and 3412E Engines for Caterpillar Built Machines Unit Injector Wiring
583R Pipelayer Power Train Final Drive, Steering Clutch, and Brakes - Separate
583R Pipelayer Power Train Final Drive, Steering Clutch, and Brakes - Connect
3406C Engines for Caterpillar Built Machines Engine Support (Rear)
3176C and 3196 Engines for Caterpillar Built Machines Fuel Priming Pump
IT14G Integrated Toolcarrier and 914G Wheel Loader Standard Power Train Differential
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0041 FMI 06 Sensor Power Supply (8 DCV) Current Above Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0262 FMI 03 Sensor Power Supply (5 DCV) Voltage Above Normal - Test