Final Drive, Steering Clutch and Brake - Remove
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | FT-1952     | Axle Removal Tool     | 1     |
B     | 8T-3207     | Lift Bracket     | 1     |
1A-5405 | Bolt 5/8 inch - 11 × 5 inch long     | 2     | |
1D-4720 | Nut 5/8 inch - 11     | 2     | |
5P-8247 | Washer 5/8     | 4     |
Start By:
- Separate the track.
- Turn the final drive until drain plug (1) is on the bottom, as shown. Remove drain plug (1) and drain approximately 11.4 L (3 US gal) of oil from the final drive.
Show/hide table
Illustration 1 | g00505143 |
- Remove the three bolts and the cover from the final drive. Remove the O-ring seal from the cover.
- Use Tooling (A) and remove the outer axle shaft.
- Use Tooling (A) and remove the inner axle shaft.
- Adjust the top bracket on Tooling (B) so that distance (X) is 63.5 mm (2.5 inch). The lower mounting bracket must be installed with the spacers (2) against the sprocket.
Show/hide table
Illustration 2 | g00505144 |
- Remove two bolts from the sprocket segments. Fasten a hoist, and install Tooling (B) on the final drive, as shown.
Show/hide table
Illustration 3 | g00505145 |
- Remove 26 bolts (3) that hold the final drive and the steering clutch and brake to the frame.
Show/hide table
Illustration 4 | g00505146 |
- The weight of the final drive and the steering clutch and brake assembly is 682 kg (1503 lb). Remove two bolts (5) that hold the steering clutch and brake to the frame.
Show/hide table
Illustration 5 | g00505147 |
Show/hide table
NOTICE |
---|
Do not remove four bolts (4) that hold the final drive to the steering clutch and brake. |
- Use Tooling (B) and a hoist, and remove the final drive and the steering clutch and brake as a unit.
Caterpillar Information System:
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Piston Pump (Steering) - Remove
836G Landfill Compactor and 834G Wheel Dozer Plate Locations and Film Locations
836G Landfill Compactor and 834G Wheel Dozer Radiator Grill - Clean
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Inverter Valve (Secondary Brake) - Assemble
836G Landfill Compactor and 834G Wheel Dozer Specifications
583R Pipelayer Engine Supplement Engine Side Guards - Remove and Install
3406C Engines for Caterpillar Built Machines Front Housing and Covers
3304B and 3306B Engines for Caterpillar Built Machines Cylinder Head - Remove
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Retaining Ring and Pin (Body) - Remove and Install
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Implement Hydraulic Operational Checks
3408E and 3412E Engines for Caterpillar Built Machines Valve Rocker Arms, Lifters, and Bridges
3176C and 3196 Engines for Caterpillar Built Machines Fuel Transfer Pump
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Hitch Position Linkage Adjustment
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Piston Pump (Steering) - Install
950G Wheel Loader and 962G Wheel Loader Electrohydraulic System Fan Drive Speed - Test and Adjust
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Service and Parking Brake (Rear) - Remove
69D, 769D , 773D, 773E, 776D, 777D, 784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Braking System Electronic Control Module (ECM)
784C and 785C Off-Highway Trucks Machine Systems Traction Control Valve - Remove
836G Landfill Compactor and 834G Wheel Dozer Steering Cylinder Bearings - Lubricate
836G Landfill Compactor and 834G Wheel Dozer Lift Cylinder Upper Trunnion Bearing - Lubricate
3406C Engines for Caterpillar Built Machines Accessory Drive
784C and 785C Off-Highway Trucks Machine Systems Traction Control Valve - Install
836G Landfill Compactor and 834G Wheel Dozer Transmission Oil - Change
3408E and 3412E Industrial Engines Unit Injector