Lifting and Tying Down the Machine - 771D Quarry Truck
Show/hide table
 | |
| Illustration 1 | g00865808 |
Show/hide table
| NOTICE |
|---|
Improper lifting or tie-downs can allow the machine to shift. This can cause damage to the machine. |
- Weight and instructions are listed herein. This information is applicable to units that are manufactured by Caterpillar.
A complete truck weighs 36100 kg (79600 lb).
- For lifting objects, use properly rated cables and properly rated slings. Position the crane for a level machine lift.
- Spreader bar widths should be sufficient for preventing contact with the machine.
- Use the two rear holes and two front holes that are provided for tie-downs.
Install the tie-downs at several locations. Place blocks under the front wheels and under the rear wheels.
Check the appropriate laws that govern the weight of the load. Check the appropriate laws that govern the width of the load and the length of the load.
Consult your Caterpillar dealer for shipping instructions for your machine.
Caterpillar Information System:
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0672 FMI 08 Speed Sensor (Torque Converter Output) Abnormal Signal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0672 FMI 04 Speed Sensor (Torque Converter Output) Voltage Below Normal - Test
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0672 FMI 03 Speed Sensor (Torque Converter Output) Voltage Above Normal - Test
3406C Engines for Caterpillar Built Machines Cylinder Block
3114, 3116 and 3126 MUI Engine Governors Governor Performance Data
3306C Engines for Caterpillar Built Machines Engine Oil Pan
143H and 163H Motor Graders All Wheel Drive Accumulator (All Wheel Drive) - Test
793B Off-Highway Truck Air System and Brakes Electronic Control Module (Brake)
D250E Series II and D300E Series II Articulated Trucks Steering, Suspension, and Body Hoist Hydraulic Systems Tailgate Cylinder - Test
836G Landfill Compactor and 834G Wheel Dozer Hydraulic System Oil Level - Check
854G Wheel Dozer Stopping the Engine if an Electrical Malfunction Occurs
966G Wheel Loader and 972G Wheel Loader Power Train Speed Sensor (Transmission Output)
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Diverter Valve (Parking Brake Release) - Remove
3176C and 3196 Engines for Caterpillar Built Machines Engine Support (Front)
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0826 FMI 03 Temperature Sensor (Torque Converter Oil) Voltage Above Normal - Test
784C, 785C and 785C HAA Off-Highway Truck Air System and Brakes General Information
572R Pipelayer Power Train Final Drive Planetary Carrier (In Chassis) - Install
784C, 785C and 785C HAA Off-Highway Truck Air System and Brakes Operational Checks
784C and 785C Off-Highway Trucks Machine Systems Steering Link - Remove and Install
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Gear Pump (Hoist and Brake) - Remove
836G Landfill Compactor and 834G Wheel Dozer Hydraulic Tank Breaker Relief Valve - Clean
784C, 785C and 785C HAA Off-Highway Truck Air System and Brakes Brake System Troubleshooting
988G Wheel Loader Power Receptacle
CB-534C Vibratory Compactor Cooling System Coolant (ELC) - Change