Limit Switch (Transmission Neutralizer) - Adjust
Show/hide table
 | |
| Illustration 1 | g00475125 |
Location of the Transmission Neutralizer Switch | |
Show/hide table
 | |
| Illustration 2 | g00489484 |
Left Service Brake Pedal (1) Plug. (2) Adjustment screw. | |
- Move the machine to a hard, level surface. The surface must also be dry and free of debris. Engage the parking brake.
- Start the engine. Run the engine at low idle.
- The transmission neutralizer override switch needs to be in the LOCKED position. Remove plug (1). Plug (1) is located on the front of the base for the left brake pedal.
- Make sure that the left brake pedal is in the RELEASED position. Use a 1/8 inch allen wrench in order to turn adjustment screw (2). Turn adjustment screw (2) clockwise in order to increase travel of the service brake before the transmission neutralizer switch is actuated. Turn adjustment screw (2) counterclockwise in order to decrease travel of the service brake before the transmission neutralizer switch is actuated.
Note: The final setting of the transmission neutralizer switch depends on the preference of the operator. Generally, the neutralizer switch is adjusted so that the switch disengages the transmission after approximately two or three degrees of brake pedal travel.
Caterpillar Information System:
980G Wheel Loader Braking System Service Braking System Pressure - Test
3304B and 3306B Engines for Caterpillar Built Machines Camshaft - Remove and Install
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Steering and Brake Manifold Valve
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Service Brake
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Parking Brake
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Parking Brake Control
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System General Information
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Gear Pump
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Brake Valve
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Accumulator Manifold
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Steering and Brake Manifold Valve
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Service Brake
550, 570 and 580 Wheel Harvesters Oil Filter (Power Train Charging System) - Replace
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Implement Hydraulic Pump
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Pilot Control Valve - Assemble
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Pressure and Flow Compensator Valve
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Transmission Heater
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Pump Drive
D250E Series II and D300E Series II Articulated Trucks 3306B Engine Supplement Battery - Remove and Install
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Implement Control Valves - Flow Priority
3406C Engines for Caterpillar Built Machines Fuel Transfer Pump
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Implement Control Valves - Parallel Logic
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Hydraulic Oil Lines
AP-1050B and BG-245C Asphalt Pavers Plate Locations and Film Locations