Camshaft - Remove and Install
拆卸步骤
开始:
- 拆下气门挺杆。 请参考解体与组装, "挺杆总成 - 拆卸和安装"。
- 拆下正时齿轮盖。 请参考解体与组装, "前壳体 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 转动曲轴至 1 缸活塞压缩行程的上止点。 曲轴齿轮上的 "C" 标记与凸轮轴齿轮上的 "C" 标记对准。
Show/hide table
图 1 | g00476744 |
- 拆下螺栓、锁片和垫圈 (1) 。
Show/hide table
图 2 | g00476743 |
注: 在位置 (A) 上的燃油喷油泵驱动齿轮和惰齿轮的轮齿上作一个标记。 这将有助于在凸轮轴拆卸和安装过程中保持发动机正时正确。 在位置 (B) 上的惰齿轮的轮齿和凸轮轴齿轮 (2) 的轮齿上作一个标记。 在安装凸轮轴时,当位置 (A) 的标记对准了位置 (B) 的标记,并且曲轴齿轮上的 "C" 标记对准了凸轮轴齿轮上的 "C" 标记,则发动机正时正确。
- 从发动机上小心地拆下凸轮轴 (3) 。
Show/hide table
图 3 | g00535590 |
Show/hide table
注意 |
---|
拆卸凸轮轴时不要损坏凸轮或轴承。 |
- 如有必要,拆下将凸轮轴驱动齿轮 (2) 固定到凸轮轴上的螺栓,然后拆下齿轮。
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将凸轮轴驱动齿轮 (2) 在凸轮轴端 (3) 上放置到位。 安装螺栓,将凸轮轴驱动齿轮 (2) 固定到凸轮轴 (3) 上。 将螺栓拧紧至扭矩 55 ± 7 N·m (41 ± 5 lb ft)。
Show/hide table
图 4 | g00535590 |
- 将 8T-2998 凸轮轴润滑剂 仅涂覆在凸轮轴凸轮上,将清洁的发动机机油涂覆在轴承轴颈上。
Show/hide table
注意 |
---|
安装凸轮轴时不要损坏凸轮或轴承。 |
- 将凸轮轴 (3) 小心地安装到发动机上。
注: 在安装凸轮轴 (3) 过程中,以两个方向旋转凸轮轴,来避免凸轮轴轴承孔粘合。
- 确保燃油喷油泵驱动齿轮和惰齿轮的轮齿上的标记与位置 (A) 对准。 确保惰齿轮和凸轮轴齿轮 (2) 上的标记与位置 (B) 对准。 将曲轴齿轮上与凸轮轴齿轮 (2) 上的 "C" 标记对准。 在全部正时标记都对准后,则发动机正时即是正确的。
Show/hide table
图 5 | g00476743 |
Show/hide table
图 6 | g00476744 |
- 安装垫圈 (1) 、锁片和两根螺栓,将凸轮轴在发动机上固定到位。
End By:
- 安装气门挺杆。 请参考 解体与组装, "挺杆总成 - 拆卸和安装"。
- 安装正时齿轮盖。 请参考 解体与组装, "前壳体 - 安装"。
Caterpillar Information System:
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Steering and Brake Manifold Valve
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Service Brake
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Parking Brake
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Parking Brake Control
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System General Information
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Gear Pump
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Brake Valve
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Accumulator Manifold
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Steering and Brake Manifold Valve
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Service Brake
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Brake Valve
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Brake Accumulator
980G Wheel Loader Braking System Service Braking System Pressure - Test
980G Wheel Loader Braking System Limit Switch (Transmission Neutralizer) - Adjust
550, 570 and 580 Wheel Harvesters Oil Filter (Power Train Charging System) - Replace
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Implement Hydraulic Pump
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Pilot Control Valve - Assemble
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Pressure and Flow Compensator Valve
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Transmission Heater
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Pump Drive
D250E Series II and D300E Series II Articulated Trucks 3306B Engine Supplement Battery - Remove and Install
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Implement Control Valves - Flow Priority
3406C Engines for Caterpillar Built Machines Fuel Transfer Pump
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement, Steering and Brake Hydraulic Systems Implement Control Valves - Parallel Logic