Lift Kickout Control - Remove and Install
Removal Procedure
Start By:
- Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Note: The lift kickout control is located at the rear end of the left lift arm.
- Disconnect electrical connector (2) .
Show/hide table
 | |
| Illustration 1 | g00342452 |
- Remove two bolts (1) and lift kickout control (3) .
- Remove two bolts (4) and magnet assembly (5) .
Installation Procedure
Show/hide table
| | |
| Illustration 2 | g00342452 |
- Install magnet assembly (5) and two bolts (4) .
- Install lift kickout control (3) and two bolts (1) .
- Connect electrical connector (2) .
- Adjust the lift kickout. Refer to Operation and Maintenance Manual, SEBU7018 for additional information.
End By: Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Caterpillar Information System:
966G Wheel Loader and 972G Wheel Loader Power Train CID 0621 FMI 04 Push Button Switch (Downshift) Voltage Below Normal - Test
793C Off-Highway Truck Fuel System Secondary Filter - Replace
CP-563C and CS-563C Vibratory Compactors Gauges
793B Off-Highway Truck Fuel System Primary Filter - Clean
966G Wheel Loader and 972G Wheel Loader Power Train CID 0621 FMI 03 Push Button Switch (Downshift) Voltage Above Normal - Test
784B and 785B Off-Highway Truck/Tractors Air Dryer - Check
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Power Train CID 0617 FMI 06 Magnetic Switch (Air Inlet Heater Relay) Current Above Normal - Test
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Power Train CID 0617 FMI 05 Magnetic Switch (Air Inlet Heater Relay) Current Below Normal - Test
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Power Train CID 0617 FMI 03 Magnetic Switch (Air Inlet Heater Relay) Voltage Above Normal - Test
784B and 785B Off-Highway Truck/Tractors Air Tank Moisture and Sediment - Drain
966G Wheel Loader and 972G Wheel Loader Power Train CID 0585 FMI 02 Speed Sensor (No. 1) (Transmission Output) Incorrect Signal - Test
IT14G Integrated Toolcarrier and 914G Wheel Loader Braking System Master Cylinder
966G Wheel Loader and 972G Wheel Loader Power Train CID 0631 FMI 03 Modulating Valve (Clutch 1 Solenoid) Voltage Above Normal - Test
966G Wheel Loader and 972G Wheel Loader Power Train CID 0631 FMI 05 Modulating Valve (Clutch 1 Solenoid) Current Below Normal - Test
Oil Renewal System Electronic Control System
966G Wheel Loader and 972G Wheel Loader Power Train CID 0631 FMI 06 Modulating Valve (Clutch 1 Solenoid) Current Above Normal - Test
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Vane Pump (Implement, Pilot and Braking) - Disassemble
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Vane Pump (Implement, Pilot and Braking) - Assemble
VFS50 and VFS70 Versatile Flotation System Front and Rear Idlers - Disassemble
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement Control Levers
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Implement Flow Control
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Inching Clutch Control
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors PTO Shield Adjustment
Challenger 35, Challenger 45 and Challenger 55 Agricultural Tractors Rear Window Grommet